The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. The wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yield stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respectively, and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. 15 Wd e

The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. The wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yield stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respectively, and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. 15 Wd e

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 290mm, b = 170mm, c = 70mm, and 0 = 35°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 37 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket Answers: Tpin 8 = i Bell crank i a B MPa MPa F₂
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
The bell crank shown is in equilibrium for the forces acting in rods (1) and (2). The bell crank is supported by a 12mm diameter pin at B that acts in single shear. The thickness of the bell crank is 5mm. Assume ?=68??, ?=155??, ?1=1150???? ?=480. Determine the following: a.the shear stress inpin B. b.the bearing stress in the bell crank.
The bell-crank mechanism shown is in equilibrium for an applied load of F₁ = 10 kN applied at A. Assume a = 300 mm, b = 110 mm, c = 80 mm, and 0 = 70°. The pin at B has a diameter of d = 12 mm and an ultimate shear strength of 450 MPa. The bell crank and the support bracket each have an ultimate bearing strength of 575 MPa. Determine (a) the factor of safety in pin B with respect to the ultimate shear strength. (b) the factor of safety of the bell crank at pin B with respect to the ultimate bearing strength. (c) the factor of safety in the support bracket with respect to the ultimate bearing strength. (1) Answers: (a) FSg= (b) FSg= (c) FSB = i Mi i a Bracket B B →-8 mm 6 mm b 6 mm Connection detail 130⁰
- The bell-crank mechanism is in equilibrium for an applied load of F₁ = 15 kN applied at A. Assume a = 270mm, b = 170mm, c 70mm, and 9 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 34 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket a B b
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 820 mm2. Assume a = 1.2 m, b = 7.3 m, and c = 3.3 m. If P = 55 kN and Q = 70 kN, determine the normal stress in each member.
Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w =775 lb/ft. Two concentrated loads also act on the rod: P= 2500 lb and Q = 800 lb. Assume a = 11 in. and b = 22 in. Determine the normal stress in the rod at the following locations: (a) x = 7 in. (b) x = 21 in. w a Answer: Ox=7in. = i psi Ox=21in. i psi
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a = 250mm, b = 170mm, c = 80mm, and 0 = 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket A Answers: Tpin B = i Ob= i Bell crank a B b MPa MPa
please help
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 135 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Answer: Pmax i kN
The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a diameter of 13 mm and the steel pins at A, B and C have a diameter of 10 mm. The yield stress of the steel in tension is 250 MPa and in shear is 125 MPa. C 1.2 m 0.9 m 0.3 m Determine the factor of safety for the pin at B with respect to yielding? Input your answer to two decimal places.