The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' 28 MPa and fy = 413.70 MPa. 750 mm 175 mm 100d mm 9-36 mm diameter bars 350 mm

The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' 28 MPa and fy = 413.70 MPa. 750 mm 175 mm 100d mm 9-36 mm diameter bars 350 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Wrong soluton will be reported and downvoted
Please give mathematical explanation with answer
The common precast members used in conjunction with prestressed concrete are?
A simply supported beam (Span = 25 ) has a seetion as shown below with normal-weichs concrete compressive strength fc- 4000 psi (normal weight, and steel reinforcement,fy=40,000 psi 1- find the modulus of rupture of the concrete per ACI318-10 2- find gross section properties to calculate the crracking bending moment (Mcr) 3-check whether the cross section is over -or under -reinforced 4-caclculate the nominal flexural strength of the cross section (Mn)
Locate the centroid (x̅, y̅)of the following composite areas
Fluid mechanics
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
Wood planks are used on each working level. The deck width/bearer span is 5 ft.. The bearers and posts are standard pipe and the pipe material is A36 steel with a yield stress of 36,000 psi and modulus of elasticity of 29,000,000 psi. Bearers are to be located at a vertical spacing of 10 ft (largest, lowest post height). Posts are to be 7 ft oc (plank length) parallel to the building wall and 5 ft apart (bearer length) perpendicular to the building wall. There are four working levels and the anticipated scaffold loading will be med duty. A. Assuming the ultimate bending strength of the planks is 3,800 psi (apply a 4:1 F.O.S.), determine the required minimum plank thickness to the nearest 100th. B. Based on the bearer material provided, what is the minimum pipe size that can be safely used? See Appendix 2 in your textbook for steel pipe properties. C. Based on the post material provided, can a 2” standard pipe be used safely? Be sure it satisfies buckling stress conditions only.
Derve the maximum steel ratio and the recommended steel ratio. show solution and explanation.
I need the answer as soon as possible
Determine the average shear stress developed in the wood fibers that are oriented along section a-a at 40° with the axis of the block. The section of the block measures 80 mm(width) x 120 mm(height) and is subjected to a 4kN compressive force. *
Determine the y-bar centroid of the composite figure shown. Where x1%-68; x2=100 and y3D84 x1 x2 - y