The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 100d mm 9-36 mm dipmeter bars 350 mm O 0o O0o

The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 100d mm 9-36 mm dipmeter bars 350 mm O 0o O0o

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(QI-B) Put (True) or (False) for the following, 1. In doubly reinforcement of RC beams. it the provided steel reinforcement ratio should be more than the maximum reinforcement ratio as specified in ACI 318-19 requirements of singly beam. 2. In working strength method, allowable tensile stress in (280 MPa) yield strength deformed steel bars used in reinforced cement concrete is (140 MPa). 3. In ultimate strength method, the factor of safety for bending strength is more than the shear strength of the beam, when the beam designed as under-reinforced section. 4. As ACI 318-19, the minimum nominal cover specified for beam is 25 mm? 5. Live loads are always taken 100% when it used in calculations of long Rerm deflection of reinforced concrete beams.
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B 30'-0"- B2 -EQ.- EQ. -EQ. SEC 1 -40'-0" IS B1 B3 B3 B1 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in². EQ. 40'-0" B EQ. North
need answer thank you
4
A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-020 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 8.003 in 3 decimal places =
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following is most likely true about the strain in the extreme tension steel? Use the tables posted to Canvas as needed (The ones in the back of the book). The strain is = 0.005
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
pls help me.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPaa) depth of the compression blockb) strain in the tension reinforcementc) moment reduction factor