With fy 60,000 psi, select the reinforcing for T-beam AB for the floor system shown. The live load is 80 psf, while the dead load in addition the concrete's weight is 100 psf. Concete is assumed to weigh150 lb/ft. The slab is 4 inches thick, the effective depth is 24 inches, and the width of the web is 15 inches.

With fy 60,000 psi, select the reinforcing for T-beam AB for the floor system shown. The live load is 80 psf, while the dead load in addition the concrete's weight is 100 psf. Concete is assumed to weigh150 lb/ft. The slab is 4 inches thick, the effective depth is 24 inches, and the width of the web is 15 inches.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hope your help concrete design CE 410 thanks
A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three No. 11 bars so that As-4.68 in.². The normal-weight concrete compressive strength is 5000 psi. and the tensile strength (modulus of rupture) can be calculated as per ACI318-14. The Grade of the steel is 60. Determine the nominal moment strength M, and the moment capacity Mn. b=12 in. Figure 1. d=24 in. h=26 in.-
Principles of Reinforced Pre-stressed Concrete
Subject is reinforced concrete design show all steps
ASAP DONT REJECT ME, I'LL GIVE UPVOTE THANK YOUU Solve the basic development lengths in tension for the following deformed bars embedded in normal-weight concrete. State if you have assumptions. (a) 12mm bar dia; 32 mm bar dia. fy = 41.4 MPa fy = 413.7 MPa (b) 44mm bar dia; 57 mm bar dia. f c = 28 MPa fy = 552 MPa
L (m)=2.8 h (mm)=375 hs (mm)=325 b (mm)=275 (Ơst)allow (MPa)=150 (Ơconc)allow (MPa)= 18
Given the section and plan view of the structural elements (Foundation and Column), estimate the concrete material quantities to be used in construction. There are sixteen (16) - C3F2 in the entire structure. Consider only from the foundation base up to the Natural Ground Level (NGL). The concrete is to have a minimum compressive strength of 3500 psi (24 Mpa).
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with a 4-20mm diamter bars and at the top with 2-16 mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 32.09 MPa and steel yield strength fy=345 MPa for 20mm bars and fy=275 MPa for 16mm bars. Determine the maximum steel area for a tension-conctrolled singly reinforced condition in positive bending with the given material strength.
rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
Principle of Reinforced Concrete Design