The 2nd Law of Thermodynamics Refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.16 MPa, and leavesas superheated vapor at 0.9 MPa and 70◦C at a rate of 0.08 kg/s. Determine the rates of energy transfers bymass into and out of the compressor. Assume the kinetic and potential energies are negligible.

The 2nd Law of Thermodynamics Refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.16 MPa, and leavesas superheated vapor at 0.9 MPa and 70◦C at a rate of 0.08 kg/s. Determine the rates of energy transfers bymass into and out of the compressor. Assume the kinetic and potential energies are negligible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerant flows through a water-cooled condenser at a rate of 25 kg/ min. The specific enthalpy of refrigerant entering the condenser is 400 kJ/kg, and leaving, is 220 kJ / kg. Determine the mass flow of cooling water through the condenser for a temperature increase of the water of I 0° C, assuming no external heat exchanges.
A compressor performs 200 hp of shaft work to compress 0.2 kg/sec of steam from saturated vapor at 147degC to state 2 with P2, T2 = 2 MPa and 357degC. The compressor is NON-adiabatic so it is also transferring heat to the surroundings in the process. Determine the heat transfer rate from the compressor. You can assume the changes in velocity and height of the system are negligible.
THERMODYNAMICS Steam at 0.6 MPa, 200°C enters an insulated nozzle at a velocity of 50 m/s. The steam is then released. It leaves it with a pressure of 0.15 MPa and a velocity of 600 m/s. Determine the final temperature when the steam is superheated in the final state and the quality when it is saturated.
Steam at 50 bar and 600°C enters an adiabatic turbine and leaves as saturated vapor at 1.5 bar. The elevation of the entrance is 3 m above the exit. The velocities at the entrance and exit are 3 m/s and 0.3 m/s, respectively. a. What is the specific power produced in the turbine? Answer: 972.96 kJ/kg b. How much do potential and kinetic energies contribute to this power? Answers: Kinetic Energy Contribution = 4.6 x 104% Potential Energy Contribution = 2.98 x 105%
3.9 m3/s of saturated water vapor enters a compressor at 250 kPa and leaves it with a pressure equal to 1400 kPa. Assume the process to be isentropic. Determine the work rate necessary to the nearest kW.
In a large refrigeration plant it is necessary to compress a fluid, which we willassume to be an ideal gas with constant heat capacity, from a low pressure P1 to a a much higher pressure P2. If the compression is done in a single compressor that operates reversibly and adiabatically, obtain an expression for the work needed for the compression in terms of the mass flow rate, P1, P2, and the initial temperature, T1. (Please write assumptions)
Problem 4 A 0.15-m rigid tank initially contains R-134a as saturated vapor R-134a at 0.6 MPa. The tank is connected by a valve to a supply line that carries R-134a at 1 MPa and 26°C. The valve is now opened, allowing the refrigerant to enter the tank, and is closed when it is observed that the tank contains only saturated liquid at 0.8 MPa. Neglecting kinetic and potential energy changes, determine, 1 MPa 26°C R-134a 0.15 m a) The mass of the refrigerant that entered the tank, in kg b) The amount of heat transfer to or from the surroundings in kJ
You have an adiabatic steam turbine. The steam enters a 0.1m diameter pipe at 200 m/s and it at state conditions of 773K and specific volume of 0.0482 m?/kg. When it exits the turbine as a saturated mixture at 393K its specific volume is 0.665 m²/kg. Using the first law for control volumes, find the work output of the turbine. You can neglect the change in KE and PE.
Refrigerant R-134a enters a steady-flow compressor at 5 °C and as a saturated vapor. a) The refrigerant follows a reversible, adiabatic process in the compressor and leaves at 1.5 MPa. The mass flow rate of the R-134a through the compressor is 0.02 kg/s. Neglecting changes in kinetic energy, calculate the power required by the compressor and the temperature of the R-134a as it leaves the compressor. b) Suppose the compressor in part (a) has friction that generates entropy as the refrigerant flows through the compressor at a rate of 1.5 (J/K) /s. What power would be required by this compressor and what would be the temperature of the refrigerant as it leaves the compressor?
Refrigerant 134-a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at 100 kPa with quality of 20 percent and leaves at 100kPa and -26 C as shown in Figure 2. If the compressor consumes 600 W of power and the COP of the refrigerator is 1.2 determine: - The mass flow rate of the refrigerant The rate of heat rejected to the kitchen air la Condenser W. X Expansion valve 100 kPa x-0.2 Compressor Evaporator e 100 kPa 260
Air (MW=29 kg/kmol) at 115.00 kPa and 285.00 K is compressed steadily to 600.0 kPaThe mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60, calculate the following. What is the actual work interaction term? What is the actual exit temperature of the air?
Question 2. Refrigerant-134a enters an adiabatic compressor as saturated vapor at 120 kPa at a rate of 0.3 m³/min and exits at 1-MPa pressure. The isentropic efficiency of the compressor is 80 percent. Determine the following: 1 MPa R-134a COMPRESSOR 120 kPa Sat. vapor Figure Q2 (a) The temperature of the refrigerant at the exit of the compressor. (b) What is the quality, x₂, of the Refrigerant-134a at the exit of the compressor? (c) The power input, in kW.