Consider a 12 cm internal diameter, 14 m long circular duct whose interior surface is wet. The duct is to be dried by forcing dry air at 1 atm and 15oC throught it at an average velocity of 3m/s. The duct passes through a chilled roo, and it remains at an average temp of 15oC at all time. Determine the mass transfer coeeficient in the duct.

Consider a 12 cm internal diameter, 14 m long circular duct whose interior surface is wet. The duct is to be dried by forcing dry air at 1 atm and 15oC throught it at an average velocity of 3m/s. The duct passes through a chilled roo, and it remains at an average temp of 15oC at all time. Determine the mass transfer coeeficient in the duct.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.29P

See similar textbooks

Similar questions

answer given are correct
Air at 20°C and 1 atm flows through a cylindrical tube made of naphthalene at a velocity of 5 m/s. The diameter of the tube is 0.1 m. Using the correlations, calculate the mass transfer coefficient for this setup. Then, compare this result with the mass transfer coefficient from the Reynolds Analogy, Prandtl Analogy, Von Karman Analogy, and Chilton-Colburn Analogy. The effectivity diffusivity is 4.24 x 10-6 m2/s.
Use the definition of the Sherwood number to calculate the mass transfer coefficient (in cm/s) for a scenario where the characteristic length is 0.034 m, the diffusivity is 0.00099 cm^2/s, and the Sherwood number is 3.5.
• Problem 1 • Air at 40 oC and 1 atm flows over a 5 m long wet plate with an average velocity of 2 m/s to dry the surface. Using analogy between heat and mass transfer. Determine the mass transfer coefficient on the plate. • Extra information: at 40 oC and 1 atm, v= 1.702 *10-5 T2.072 • DAB 1.87 x 10-5 X P
Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is
During air cooling of oranges, grapefruit, andtangelos, the heat transfer coefficient for combined convection,radiation, and evaporation for air velocities of0.11 < V < 0.33 m/s is determined experimentally and isexpressed as h = 5.05 kair Re1/3/D, where the diameter Dis the characteristic length. Oranges are cooled by refrigeratedair at 5°C and 1 atm at a velocity of 0.3 m/s. Determine(a) the initial rate of heat transfer from a 7-cm-diameterorange initially at 15°C with a thermal conductivity of0.50 W/m·K, (b) the value of the initial temperature gradientinside the orange at the surface, and (c) the value of theNusselt number.
AB (21.5-18) f b. Pe с. В 21.1-1 21.1-2. Conversion of Mass-Transfer Coefficients. Prove or show the following relation- ships, starting with the flux equations: (a) Convert k to k, and kG. (b) Convert k to k and k. (c) Convert kG to k, and ke. ET 619 Part 1 Transport Processes: Momentum, Heat, and Mass
Saturated steam at 1 atm condenses on a 3-m-high and 5-m-wide vertical plate that is maintained at 90 0C by circulating cooling water through the other side. Determined (a) the rate of heat transfer by condensation to the plate, and (b) the rate at which the condensate drips off the plate at the bottom (Please use the condensation formulations at the Geankoplis).
An 80m deep and 100m wide river flows from the left to the right off the page. An action will release two sources of oil to the river: (1) the indirect runoff of oil accumulated on a bridge that runs off site and crosses over the river and (2) the direct and permitted discharge of water containing oil from the activities onsite (a water pollution control plant) to the river. The oil has a molecular weight of 100 g/mol, it fully dissolves in the river water, and it decays in the river with a rate constant of 0.2 d-1. Estimate the potential impact of this action on the concentration of oil in the river at a location 500m downstream of the WPCP. (1) bridge runoff Q1 = 1 m's C = 1 mol/m (2) WPCP discharge Q2 = 50 m's C2 = 0.01 mol/m Qin = 1000 m³'s Cin = 0.001 mol/m? --500m- 500m- -500m 80m 100m a. Recommend the x, y, and z dimensions of the CV. Justify your recommendations. b. Estimate the oil concentration in the water 500m downstream of the WPCP assuming steady and 1D mixed. c. Sketch…
One house owner with a pond on his property has decided to use the pond water to cool his house. His idea is to flow air through a thin smooth 10-cm-diameter copper tube that could be submerged into the pond. The water in the pond, at few meters below the surface is typically maintained at a constant temperature of 15°C. If he assumes the air (~1 atm) entering the copper tube at a mean temperature of 30°C with an average velocity of 2.5 m/s, determine the necessary copper tube length that would be needed so that the outlet mean temperature of the air is 20°C. You may consider the convection heat transfer coefficient of 1000 W/m2·K on the outer surface of the copper tube, between the pond water and copper tube. Since the copper tube is thin, the conduction resistance of the tube wall may be neglected.
Air with dby bulb temperature of 25C PSAT = 3.169kpa and wet bulb temperature of 15C PSAT=1.7051 kpa flows in round duct of diameter 800m with velocity of 7m/S Determine Mass flow rate (answer. 249kg/min) Mass flow rate of dry air (answer 247 kg/min)
In an absorption tower, ammonia is absorbed from air at atmospheric pressure by aceticacid. The flowrate of 2 kg/m2s in a test corresponds to a Reynolds number of 5100 andhence a friction factor R/ρu2 of 0.020. At the temperature of absorption the viscosity ofthe gas stream is 0.018 mNs/m2, the density is 1.154 kg/m3 and the diffusion coefficientof ammonia in air is 1.96 × 10−5 m2/s. Determine the mass transfer coefficient throughthe gas film in kg/m2s (kN/m2) Explain briefly .