The 2nd Law of Thermodynamics Air is compressed from 12 psia and 77.3◦F to a pressure of 145 psia while being cooled at a rate of 15Btu/lbm by circulating water through the compressor casing. The volume flow rate of the air at the inletconditions is 6000 ft3/min, and the power input to the compressor is 800 hp. Determine (a) the mass flow rate of the air (b) the temperature at the compressor exit

The 2nd Law of Thermodynamics Air is compressed from 12 psia and 77.3◦F to a pressure of 145 psia while being cooled at a rate of 15Btu/lbm by circulating water through the compressor casing. The volume flow rate of the air at the inletconditions is 6000 ft3/min, and the power input to the compressor is 800 hp. Determine (a) the mass flow rate of the air (b) the temperature at the compressor exit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Before entering the engine of a BMW320D, air drawn in at 20°C and atmospheric pressure enters the compressor of a turbocharger at a rate of 120 litres per minute. The inlet pipe to the compressor has an internal diameter of 18 mm, the outlet pipe of the compressor has an internal diameter of 26 mm and is axially aligned with the inlet pipe. The compressor raises the pressure and temperature of the exiting air to 4 bar (absolute) and 161°C.
Thermodynamics: Please show step by step solution Thank you!
Given 603.06 kW electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Total rate of entropy production= 1.256 kJ/s K. Total rate of exergy destruction= 368.37 kW. Consider steady state conditions. 1.4) 0.015 kg is the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of the problem above. if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Answer the following: a) Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state…
solle не An adiabatic air compressor compresses 15 L/s of air at 1 bar and 30 °C to 8 bar and 350 °C. A heat loss of 10 KJ/Kg is estimated through the wall of the compressor. Determine the work required by the compressor in kJ/kg and the power required to drive the air compressor in kW.
I need the answer as soon as possible
In a steady flow apparatus, a fluid enters with a specific volume of 0.40 m3/Kg, a pressure of 550 KPa and a velocity of 20 m/s. The inlet port is 20 m above the floor and the outlet port is 20 m below the floor. The fluid exits with a specific weight of 0.012 KN/m3, a pressure of 100 KPa and a velocity of 280 m/s. The apparatus produces a 140 KJ of work per kg of fluid and a 12 KJ/Kg of heat loss occurs between the inlet and outlet ports. Determine the amount of change in the internal energy in the apparatus. Is the internal energy increases or decreases?
12 kg of air per minute is delivered by a centrifugal air compressor It enters the compressor at a velocity of 12 m/s with a pressure of 1 bar and specific volume of 0. 5 m²/kg and leaves at a velocity of 90 m/s with a pressure of 8 bar and specific volume of 0.14 m/kg. The increase in enthalpy of air passing through the compressor is (hz-hi = 150 kJ/kg) and heat loos to the surroundings at a rate of 700 kJ/min. Assume the inlet and discharge line are at the same level. Answer the following; a. What are the main assumptions b. Calculate the power required to drive the compressor, in kW c. Calculate the ratio of inlet and outlet pipe diameter? Air out Boundary d2 Centrifugal compressor di Air in
In a steady flow apparatus, 135 kJ of work is done by each kg of fluid. The mass density, pressure and velocity of the fluid at the inlet are: 2.703 kg/m^3, 600 kPa and v =16 m/s. At the outlet are: 1.613kg/m^3, 100 kPa and 270m/s. The inlet is 32 m above the discharge line. The heat loss between the inlet and discharge is 9 kJ/kg. In flowing through this apparatus, does the specific internal energy increases or decreases? Note that this problem is for you to solve Δu since it is for each kg and interpret the sign (positive or negative) of the result.
electronic components mounted on a flat plate are cooled by convection to the surroundings and by liquid water circulating through a U-tube bonded to the plate. At steady state, water enters the tube at 20∘Cand a velocity of 0.4 m/s and exits at 24∘C with a negligible change in pressure. The electrical components receive 0.5 kW of electrical power. The rate of energy transfer by convection from the plate- mounted electronics is estimated to be 0.08 kW. Kinetic and potential energy effects can be ignored. Determine the diameter .
Air (MW=29 kg/kmol) at 115.00 kPa and 285.00 K is compressed steadily to 600.0 kPaThe mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60, calculate the following. What is the actual work interaction term? What is the actual exit temperature of the air?
Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 196 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K), keeping three decimal places.
Air at a mass flow rate of 2.5 kg/s is decelerated in a diffuser from 220 m/s, with A2/A1 = 3. The device loses 18 kW of heat during its steady state operations under the following conditions: 18 kW AIR T1= 27 C T2 = 42 C, 101 kPa Determine the exit velocity and the inlet pressure of air.