Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER CORK 60 CC RESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at To = 0 ° C. (주) (주) In e a + b

Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER CORK 60 CC RESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at To = 0 ° C. (주) (주) In e a + b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the BOD concentration based on the data below. DOinitial (mg/L) 7 DO final (mg/L 3.5 Vol. sample (ml) 15 Vol. dilution (ml) 285 BOD (mg/L) ?
discuss at least five sources of error in measuring anions in rainwater through ion chromatography (label them as random or systematic errors).
ANSWER AND SHOW THE COMPLETE FREE BODY DIARGRAM. IN CLEAR EXPLANATION.
Research atleast 4 venturi meter write the problem and solution legibly draw also the diagram if there is.
MASS CUMULATIVE CUMULATIVE SIEVE # SIEVE (mm) RETAINED MASS % RETAINED (gm) RETAINED(gm) #4 4.75mm 30 #8 2.36mm #16 1.18mm 109 #30 600μm 300μm 150μm 101 #50 59 #100 117 PAN 25 TOTAL MASS OF 500 SAMPLE FM ****FILL UP THE SHADED CELLS. SHOW SAMPLE CALCULATION.
penetration of bituminous ASTM D5 - 97and AASHTO T 49-80:" Penetration of Bituminous". Why cover the sample with a cloth when coolingWhat is the degree of penetration of bituminous materials used in road construction?
Qualifying materials Quantify the materials that you used in your drum (acoustic treatment only) Sample No. Description. Quantify. Unit ¹. Rockwall insulation 1. Roll
Please upload your full solution to the following problem. Calculate the bed life, volume of water treated, minimum carbon usage rate (CUR), and maximum specific throughput for trichloroethene (TCE) given the following design specifications: ● . B Influent concentration = 1 mg/L TCE Carbon type: Calgon Filtrasorb 400 (12 x 40 mesh); Pb = 450 g/L Freundlich parameters for TCE Freundlich capacity parameter K = 55.9 (mg/g)(L/mg)1/n Freundlich intensity parameter 1/n = 0.48 Treatment objective = 0.005 mg/L TCE Flow rate = 378.5 L/min (100 gal/min) Empty bed contact (EBCT) = 10 min . ● Assume that no other solutes compete with TCE for adsorption onto the GAC, and that the GAC is saturated at the influent concentration. 201 4 He de dis
6- A liquid has a specific weight of 59 lb/ft and a dynamic viscosity of 2.75 lb . s/ft'. Determine its kinematic viscosity.
Please upload your full solution to the following problem. Determine the dosage and daily consumption of powdered activated carbon (PAC) required for trichloroethylene (TCE) removal given the following design specifications: 6 SUL Influent concentration = 1 mg/L TCE Carbon type: Calgon Filtrasorb 400 (12 x 40 mesh); pb = 450 g/L Freundlich parameters for TCE • Freundlich capacity parameter K = 55.9 (mg/g)(L/mg)¹/n • Freundlich intensity parameter 1/n = 0.48 Treatment objective = 0.005 mg/L TCE Flow rate = 378.5 L/min (100 gal/min) Assume that no other solutes compete with TCE for adsorption onto the PAC, and that the PAC is saturated at the treatment objective.
penetration of bituminous ASTM D5 - 97and AASHTO T 49-80:" Penetration of Bituminous". What is the purpose of using the weightWhat is the purpose of moving the model when heatingWhat is the use of using a water bathWhy cover the sample with a cloth when coolingWhat is the degree of penetration of bituminous materials used in road construction?
Exercise Module 8a (to be submitted into the droppbox Module 8a before Sunday Feb. 20): Describe why parameters such as pH, conductivity, sodium, chlorides, fluorides, sulfates, hardness, silica need to be controlled to prevent corrosion or scale build up in water containers/lines.