In a given setup, distilled water has been found flowing into a nozzle at a uniform velocity of three meters-per- second that reduces the pipe diameter from ten centimeters to two centimeters, as shown in the figure. What is the discharge of water in this given setup where it leaves the nozzles? 10 cm dia. 2 cm dia. 2 Note: Type only the numerical value of your final answer; in terms of liters per second

In a given setup, distilled water has been found flowing into a nozzle at a uniform velocity of three meters-per- second that reduces the pipe diameter from ten centimeters to two centimeters, as shown in the figure. What is the discharge of water in this given setup where it leaves the nozzles? 10 cm dia. 2 cm dia. 2 Note: Type only the numerical value of your final answer; in terms of liters per second

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hydraulics of Sprinkler Nozzle Example// Select the diameter of the nozzle and the working pressure for a sprinkler has a discharge of (126 m2/hour)?
Pls do it correct and neatly
please show all working and the assumptions and equations used to get final answer
A closed tank containing 2 layers of fluids is discharging its contents through an orifice as shown in the figure. The circular orifice has a diameter of 48mm with a discharge coefficient of 0.65. Considering a pressure reading of 148kPa on the surface of the fluids within the tank, determine the discharge flowing out of the orifice (in L/s)? The gasoline layer is 4.0m deep with a specific gravity of 0.69, while the water surface is 5.5m above the orifice. Air: kPa gage V Gasoline %3D D = mm Water
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER 60 cC CORK ŘESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at T, = 0°C. a + b| + T Mo b) What is the viscosity of the used motor oil at 280 K, 305 K and 320 K? You can use the above equation
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
Fluid mechanics ضهذعسو
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
Problem 1: Clogged Bathtub This bathtub cost a bundle, but even rich people occasionally have to deal with clogged drains. Part A Write the basic equation for volume balance for this system. What property of the fluid allows us to simplify from mass balance (which is always valid) to volume balance (which is not)? Part B The rich person turns on the faucet to flow at 5.0 gal/min for 15 minutes. Meanwhile, the open drain is draining at 1.0 gal/min. How much water is in the bathtub after 15 minutes? Then, how long will it take to completely drain? Part C Make a plot showing the volume of water versus time.
Answer is given, just a solution is needed.
subject: hydraulics. 3 decimal places. p.s with solution