Q. 7 In a pipe arrangement shown in Fig. 6, gasoline (density, p = 780 kg/m³) enters section 1 having a flow rate of 0.5 m³/s and exits section 2 at an average velocity of 12 m/s. What is the average velocity at section 3? Is it in or out? (2) (1) D, = 18 cm D3 = 13 cm Fig. 6

Q: the differences between CAD, CAE, CAM and CIM.

A: CAD:- Computer-aided design is defined the practice of using the computer systems in order to help…

Q: Maintain a minimum spacing between the object and the dimension and between multiple dimensions are…

A: For proper clarity and to avoid to conflict minimum spacing between the object and dimensions and…

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: What do you mean by the Bulk Richardson Number (BRN)?

A: The Bulk Richardson Number is defined as the ratio of turbulence due to kinetic energy to the shear.

Q: Locate the X-X centroidal axis for the cross section shown. £ sym. W840 x 329 W530 × 72 X X

A:

Q: 40 fé = 3000psi %3D ダク 26" 14 14 fy = 6o ksi %3D 8#8 12 NWC PMa = ?

A: A beam with T section is given in the above question. The value of fc' and fy is provided. also the…

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: AW 12 x 35 steel cantilever beam is subjected to an axial load P = 9.5 kips and a transverse loadv =…

A:

Q: Write the IUPAC name for   compound.

A: International Union of Pure and Applied Chemistry (IUPAC)) is the naming pattern or nomenclature…

Q: what was the unit used in the plan shown above ? autocad

A: There base unit in AutoCad is inch.

Q: The value of the smallest division on the main scale of a horizontal circle is graduated to 1/6 of a…

A:

Q: Find the vertical and horizontal line detect segmentation

A: Detecting vertical and horizontal lines in an image is a common task in image processing and…

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: What is bulk density? own word plss type written

A: Bulk density is the ratio of total mass of soil to the total volume of soil mass.

Q: Explain the Methods of Slices.

A: Methods of Slices may be used along the failure plan in different shearing resistance for soil.

Q: Determine centroid Y-bar with respect to X-axis, Centroid g w rupect to x-axis 8" 6"

A:

Q: Select the lightest weight stell wide-flange beam that will safely support the loading shown. The…

A: The given loading is shown below:

Q: Shape PNA L5x3x1 -X x²/16 x x5/16 x¼ PNA k Wt. Table 1-7 (continued) Angles Properties Area, A Axis…

A: As multiple questions are asked and as per the guidelines only very first question will be answered.…

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: ments Collaborate 此片 Freak Out Slice Crop Horizontal Start New Sheet Sketch Sketch Sheets 5 LBS…

A:

Q: Define the By Bowle's method ?

A: Joseph bowle presented a method/Formula to Determine Modulus of Subgrade Reaction .The Mehod is…

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: front view

Q: Arc command and its abbreviation is A character is the only command can be used to draw an arc in…

A: It is required to state whether true or false statement.

Q: EARTHWORK SPECIFICATIONS oCut and Fill to Formation Level oGeneral oFill materials oFinish to…

A: Formation is a flattened surface of ground on which the pavement is settled. A non-structural…

Q: What is ASD method

A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…

Q: The date in a business letter can not be abbreviated. * O True False

A: True

Q: show the (c)

A:

Q: If the elevation of BM-A is 975.00', what is the elevation of TBM-1? ENATAL 7.45 BS FS 5.12 6.77 BS…

A:

Q: 2 1 Matrix -1 + 2 Matrix 1 3 -2 4 A. Matrix 2 2 B. Matrix 1 1 C. Matrix -1 D. Matrix 1 5 2.

A: Given:- Two matrices are given:- A = 21-13 B = -1211 To determine:- The value of Matrix 21-13 +…

Q: e shape factor for the section as shown -3d 3d - fe 2d

A:

Q: Find

A:

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: Describe Mohr’s Circle.

A: Mohr’s circle is defined as a two-dimensional graph which represents stresses at a point.

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: Which tools that can be used to :1 draw the following shape in .AutoCAD Left-side view Top view…

A: Answer: 4. Construction Lines, Offset, Line, Trim, Layers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.