Answered: 6- A liquid has a specific weight of 59…

6- A liquid has a specific weight of 59 lb/ft and a dynamic viscosity of 2.75 lb . s/ft. Determine its kinematic viscosity.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Related questions

Q: A round vertical steel tank has an inside diameter of 3 m and is 6 m in height. It contains gasoline…

A: Given data, Inside diameter D = 3 m Height of cylinder h = 6 m Gasoline density p = 750 kg/m^3…

Q: An aluminum pipe has a length of 64 m at a temperature of 15°C. An adjacent steel pipe at the same…

A: Length of the aluminium pipe, Lu = 64m Temperature, To = 15°C Length of steel pipe,…

Q: Find the wall thickness of this rigid polyvinylchloride (PVC) tube.

A: Outer diameter=2.375ft Inner diameter=2.181 ft

Q: Estimate the tensile strength required to prevent cracking in a concretelike material that is cast…

A: Given: Length of the bar=1.25 m=49.2126 inInitial temperature= 40°C Final temperature=-20°C…

Q: 1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has…

A: Please refer the attached image for complete solution. THANK YOU.

Q: 3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the…

Q: A cylinder tank with 10 inches in diameter contains an oxygen gas at 2500 psi. Calculate the…

A: Given data, p = 2500 psi d = 10 in σT = 28000 psi

Q: A circular nylon [E = 8 GPa; v=0.35; a=20x106/°C] disk with a circular hole in its center is shown.…

Q: 4 source of error in viscosity

A: 1. Air viscosity—viscosity is affected by temperature and other causes. It is impossible to reliably…

Q: An aluminum pipe has a length of 50 m at a temperature of 6°C. An adjacent steel pipe at the same…

A: Concept Initial length = L1 at temperature T1 Due to temperature change to T2 length of the…

Q: 1A 50 mm C 175 mm B, -225 mm -300 mm- Bar ACB shown in the Figure is subjected to a uniform…

Q: of 6.0 Mpa and a tempe

Q: What loads are exerted on the ends of the tube, and what are the resultant stresses?

A: Length of the aluminum tubing L = 13 in Modulus of elasticity E = Coefficient of thermal expansion…

Q: A rectangular nylon [E = 8 GPa; ?= 0.35; ?= 24 x107 P/°C] plate has a circular hole in its center.…

A: Young's modulus, E = 8 GPaThermal coefficient, Intial temperature = 15CFinal temperature =…

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

Q: A rectangular nylon [E =8 GPa; v=0.35; a= 23x10 6/°C] plate has a circular hole in its center. At an…

Q: An aluminum pipe has a length of 52 m at a temperature of 6°C. An adjacent steel pipe at the same…

Q: Estimate the tensile strength required to prevent cracking in a concrete-like material that is cast…

A: Given data:

Q: In a compression test and for a very ductile material similar to copper , the diameter and the…

A: Initial length Lo = 80 mm Initial diameter Do = 60 mm Final diameter D = 120 mm Final length = ?

Q: A spherical stainless-steel tank having an inner diameter ‘D’, is used to store natural gas at a…

A: Given Data: The inner diameter of a steel tank is, D=620 mm The pressure of a gas is, P=25 MPa The…

Q: Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when the…

A: Given data: ΔT= 110-20= 90 oC α = 11.7 x 10-6 E = 200 GPa or 200 x 103N/mm2

Q: Question 3: The block shown is made of a magnesium alloy for which E=760GPa and 9 =0.35. Knowing…

A: a) Calculating the change in height:

Q: The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.00. Compute the equivalent…

A: Absolute viscosity, also known as dynamic viscosity. We have to calculate in stokes, and stokes is…

Q: Locate the center of gravity of the volume. The material is homogeneous.

Q: A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is…

A: Given, E= 8 GPa Ti=22˚ C Tf=46˚ C v=0.35 α=29 × 10-6/°C…

Q: the external and internal diameters of hollow cylinder are 115mm and 99mm respectively. when the…

Q: The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.40. Compute the equivalent…

A: Stokes is the unit if kinematic viscosity. Kinematic viscosity is the ratio of dynamic viscosity to…

Q: Demonstrate the concept of liquid viscosity measurements preparation

A: The resistance to flow is strongly related to viscosity, which is a property of liquids. It is…

Q: state the differences between the coefficient of thermal expansion of steel and concrete.

A: steel used with the concrete is the main reason is the coefficient of the thermal expansion is same…

Q: A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear thermal…

A: Given- side=1 m,α=1×10-5 /oC,k=200 GPa, It is needed to find the volumetric stress.

Q: Determine induced stress

A: given data : length (L)=5 mmt1=15∘Ct2=40∘C

Q: Estimate the tensile strength required to prevent cracking in a concrete-like material that is cast…

A: Given data Length of bar( L)= 500 mm Initial cured temperature (To) = 23°C Final temperature (Tf)…

Question

6- A liquid has a specific weight of 59 lb/ft and a dynamic viscosity of 2.75 lb
. s/ft'. Determine its kinematic viscosity.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Demonstrate the concept of liquid viscosity measurements preparation
A rectangular nylon [E = 8 GPa; ?= 0.35; ? = 24 ×10 6/°C] plate has a circular hole in its center. At an initial temperature of T¡ = 15°C, the plate width is b = 260 mm, the plate height is h = 160 mm, the diameter of the central hole is d = 45 mm, and the thickness of the plate is t = 17 mm. At a final temperature of Tf= 52°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. b h
Vol.strain,
Soil mechanics ضهقحشكوظز
A rectangular nylon [E =8 GPa; v=0.35; a= 23×106/°C] plate has a circular hole in its center. At an initial temperature of T₁ = 22°C, the plate widthis b=310 mm, the plate height is h = 220 mm, the diameter of the central holeis d = 60 mm, and the thickness of the plateist= 18 mm. At a final temperature of T= 59°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. Answers: (a) d = i (b) t= i b d mm mm
A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus and Poisson's ratio of the material are 150 GPa and 0.1 respectively. Determine change in volume of the block.
the external and internal diameters of hollow cylinder are 115mm and 99mm respectively. when the cylinder is compressed by an axial force of 180kn the outer diameter of cylinder increases by 115.5 x 10-4 mm . determine youngs modulus of elasticity 2x105 N/mm2 a) the increase in the inner diameter . b) the increase in the wall thickness and c) Poissons ratio of the material of the cylinder
I In a compression test and for a very ductile material similar to copper , the diameter and the length of the specimen before the test were 60mm and 80mm respectively . Find the length , in inches , after the test if the diameter became 120mm . Assume that the density remained unchanged
A spherical stainless-steel tank having an inner diameter ‘D’, is used to store naturalgas at a pressure of ‘p’. The properties of the steel are as follows: yield stress in tensionis ‘T’; yield stress in shear is ‘S’ and modulus of elasticity is ‘E’. The desired factor ofsafety with respect to yielding is ‘F.S’.Determine the minimum permissible thickness t min of the tank. (D (mm)=620)( p (MPa)=25)( T (MPa)=1000)( S (MPa)=440)( E (GPa)=208)( F.S=3.4)
Solve fast please
A circular nylon [E = 8 GPa; v=0.35; a=20x106/°C] disk with a circular hole in its center is shown. At an initial temperature of T;= 19°C, the outer diameter of the disk is D = 230 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 19 mm. At a final temperature of Tf= 52°C, determine: (a) the change in diameter Ad of the central hole (assume an increase Ad as positive, otherwise as negative). (b) the change in thickness At of the disk (assume an increase At as positive, otherwise as negative). (c) the normal strain in the circumferential direction around the outside of the disk. O Answers: (a) Ad= (b) At= (c) Ecirc 0.0363 0.01254 660 D mm mm με
* Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when the bar is heated to :110 degree A Lo Est = 200 Gpa ast 11.7 μm/m°C Ast = 200 mm² + 210.6 MPa (compression) + 210.6 MPa (Tension) _187.2 MPa (compression) +187.2 MPa (Tension) _187.2 MPa (Tension) _210.6 MPa (Tension) +187.2 MPa (compression) O 210.6 MPa (compression)