supported on a span of 4 m. The beam will support a total load of 13 kN/m including its own weight. If the allowable bending stress of wood is 12.5 MPa, select the minimum required depth mm) of the beam based on flexure.

supported on a span of 4 m. The beam will support a total load of 13 kN/m including its own weight. If the allowable bending stress of wood is 12.5 MPa, select the minimum required depth mm) of the beam based on flexure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support
The laminated beam, shown in cross section, is composed of ?ve 6- in. by 2-in. planks that are glued together. The beam carries a uniformly distributed load of intensity We over its 8-ft simply supported span. glue, 90 psi for shear in wood, and 800 psi for bending in wood, If the working stresses are 75 psi for shear in 6 in. determine the maximum allowable value of We so that the shear stress in the wood is not exceeded. A. 900 lb/ft C. 833 lb/ft determine the maximum allowable value of Wo so that the shear 1. B. 555 lb/ft D. NOTA 2. stress in the glue is not exceeded. 900 lb/ft B. 555 lb/ft D. NOTA А. C. 833 lb/ft determine the maximum allowable value of we so that the bending stress in the wood is not exceeded. 3. 900 lb/ft A. 555 lb/ft B. С. 833 lb/ft D. NOTA 5 @ 2 in. = 10 in.
A composite beam is fabricated by bolting two 3.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The moduli of elasticity of the timber and the steel are 1700 ksi and 29000 ksi, respectively. The simply supported beam spans a distance of 25 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBc = 11 ft, b = 3.6 in., d = 13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,,o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1010 psi and 26800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: LAB (a) o, = (b) P = i i B LBC b F لالها b Cross section C kips. d ksi, o, = LCD D ksi.
Determine end reactions for Beam B-1 and Girder G-1. B-1 1 F1 • L1= 24 ft L2= 6 ft Live load 30 psf 4" Thick concrete slab (density = 150 pcf) . 5/8" Thick terrazzo (12 lb/ft2/in) • Beam weight = 35 lb/ft . Girder weight = 26 lb/ft Please round to the nearest one. One end reaction for B-1 = lbs One end reaction for G-1 = lbs Please answer all parts of the question. 20 DOO 000 F2 @ 2 JAL #3 G-1 F3 54 $ F4 % 5 F5 L2 L2 L2 L2 MacBook Air F6 A 6 & 7 F7 11 ► 11 * 8 F8 F9
Floor beams of Group B timber are spaced 1.2 m centres, on a clear span of 3 m, with a bearing of 20 cm at each end. The dead load of roof covering is 2000 N/m' and live load is 1500 N/m?. Design the beam for inside location. The timber is of standard grade. Take E = 11000 N/mm?.
Example 2 (H.W) : For the simply supported beam of section shown in figure below, calculate the flexural stresses at ends and mid-span at all loading stages, then check these stresses with ACI limitations use fei' = 29 MPa, fe'= 35 MPa, Fpi= 1300 MPa, final losses =20 % live load= 5 kN/m, dead load =5 kN/m in addition to its own weight, span length= 13 m, class U and all live load is sustained. 600 mm 75 mm 700 mm I 50 mm 100 mm 100 mm
a) A singly-reinforced concrete beam 300 mm wide and 650mm deep to the center of the tensile reinforcement is reinforced with 5 bars of 18 mm diameter. Find the ultimate moment capacity of the section. Take characteristic yield strength of steel as 415N/mm2.
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
3. Three 18 mm diameter steel bolts are to be used to attach the steel plate to a wooden beam. The plate has to support a load of 110 KN. The ultimate shearing stress for the steel used is 360 MPa. Determine what will be the factor of safety for this design. HOAN
Current Attempt in Progress A composite beam is fabricated by bolting two 2.4-in.-wide by 10-in.-deep timber planks to the sides of a 0.6-in. by 10-in. steel plate. The moduli of elasticity of the timber and the steel are 1790 ksi and 28300 ksi, respectively. The simply supported beam spans a distance of 18 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD= 4 ft, LBc = 10 ft, b = 2.4 in., d = 10 in. and t = 0.6 in. (a) Determine the maximum bending stresses o,, o, produced in the timber planks and the steel plate if P = 3.4 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1450 psi and 25000 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: (a) o, = (b) P= LAB i i B LBC F Lodlod b Cross section C kips. d ksi, o, = LCD D ksi.
Describe FOOTINGS ON OR NEAR SLOPES
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.