USE NSCP 2015 A simply supported beam has a span of 7m, fc=10MPa, fs=150MPa, n=8. Assuming weight of concrete to be 2400kg/m3. Calculate the safe value of load P (acting at the midspan) that thebeam could carry. The beam cross section has b=300mm d = 500mm and clear concrete covering of 40mm. it is reinforced with 5-25mm in tension and 3 - 25mm in compressionKNP =

Given Data:L=7mfc=10mpafy 150mpan=8wt of concrete = 2400kg/m3.b=300mmd=500mmr/f tension= 5-25mmϕr/f…

A simply supported beam has a span of 7m, fc=10MPa, fs=150MPa, n=8. Assuming weight of concrete to be 2400kg/m3. Calculate the safe value of load P (acting at the midspan) that the eam could carry. The beam cross section has b= 300mm d = 500mm and clear concrete covering of 40mm. it is reinforced with 5-25mm in tension and 3-25mm in compression KN '=

A simply supported beam has a span of 7m, fc=10MPa, fs=150MPa, n=8. Assuming weight of concrete to be 2400kg/m3. Calculate the safe value of load P (acting at the midspan) that the eam could carry. The beam cross section has b= 300mm d = 500mm and clear concrete covering of 40mm. it is reinforced with 5-25mm in tension and 3-25mm in compression KN '=

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.1P

See similar textbooks

Similar questions

A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.
A rectangular beam has a width of 269mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The depth of the concrete stress block is ___.
ス F. reinforced concete structure is shown The floor framing plan oF in the figure. The beams are 280 mm wide and S20 mm deep, and the slob is 110mm thick an edditional (super impes) veight,1 and live lo ad of OTher than conerete weight, the floor subjected other to Is dead load of 3k Pa si2 k Por. Unit weight of concrete is 23.5 kN/m® le Determine the total uniform load on beam DEF and ABC axial load 20 Determme the total on columns A and B,D an) E 2Sm 티 2.Sm 6.2m 6.2m
The simply supported I-beam shown in cross-section and elevation is to carry a uniform service live load totalling 8 kN/m over 12m span, in addition to its own weight. The beam will be pretensioned using multiple seven-wire strands, eccentricity is 130mm and constant. The 28-day compressive strength of concrete is 40 Mpa. Calculate deflections
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis. QUESTIONS: 1.What is the effective depth of the given beam. (1 decimal) 2.What value of ?1 should you use in the computation. (2decimals) 3.What is the value of the steel reinforcement ratio if a balanced condition is assumed. (4decimals) 4.What is the actual steel reinforcement ratio of the given beam. (4 decimals) 5.What type of failure will occur? 6.What is the value of the compression block? You will get two values, use the positive. (4 decimals) 7.Given your answer in Numbers 5 and 6, what value of fs you should use? (4 decimals) 8.What is the nominal strength of the given section?…
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis. What is the actual steel reinforcement ratio of the givenbeam. (4 decimals) What type of failure will occur? What is the value of the compression block? You will gettwo values, use the positive. (4 decimals) Given your answer in Numbers 5 and 6, what value of fs youshould use? (4 decimals) What is the nominal strength of the given section? (4decimals) What is the maximum moment applied to the beam? (2decimals)
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis. Considering LRFD, what is the factored load to be carriedby the beam? (2 decimals) Considering LRFD, what is the reduced capacity of thesection? (4 decimals) Can the section sustainthe given loads?
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
A concrete beam of length 5.5m is built monolithically with the slab. Originally, the beam has a width of 300mm and effective depth of 400mm. If the flange of the slab is 150mm and the total area tension steel bars is 500 sq.cm., determine the design capacity of the beam structure. The concrete has a compressive strength of 25 MPa, steels' yield strength is 420 MPa. and the beam's clear span from its adjacent beams is 2.15m.
A T beam has a concrete and steel strengths of 28 MPa and 420 MPa. The live load is 3830 Pa. while the dead load in addition to concrete's weight is to be 4097. The density of concrete is 2400 kg/m³. The slab is 125 mm thick while the effective depth is 600 mm, the total height of T-beam of 675 mm and the bottom width of T beam is 375 mm. The length of the beam is 7 meters. The center-to-center spacing of beams is 330 cm. Determine the arrangement of main reinforcement bars. Check for clear spacing.
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.