The simply supported I-beam shown in cross-section and elevation is to carry a uniform service live load totalling 8 kN/m over 12m span, in addition to its own weight. The beam will be pretensioned using multiple seven-wire strands, eccentricity is 130mm and constant. The 28-day compressive strength of concrete is 40 Mpa. Calculate deflections

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 403 mm and an over-all…

A: Given Data: The width of a rectangular beam is b=403 mm. The overall-depth of a rectangular beam is…

Q: The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads…

A: In the question  calculation of load  on the beam is permissible until and unless there will no…

Q: 1. A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is…

A:

Q: s of the reinforced concrete T-beam ,hi = 4 in., b2 = 12 in., h2 = 18 in., and n = 8. Using elastic…

A: Calculate the centroidal distance of the reinforced T-beam using the equation of first moment of the…

Q: Determine the required tension steel area of the T beam with given properties below. Width of flange…

A: Given:- Width of flange, bf=500 mmWidth of web, bw=340 mmThickness of flange, tf=140 mmEffective…

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 402 mm and an over-all…

A: Given Data: The width of a beam is b=402 mm. The overall depth of a beam is D=571 mm. The distance…

Q: The total compressive force at the time of failure of a concrete beam section of width 'b' without…

A:

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy =…

A: Given data f'c = 26.27mpa fy = 414 mpa The As value was not given. so lets assume as 3bars of 32mm…

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 413 mm ar

A:

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 410 mm and an over-all…

A: Torsion in beams is caused by the action of shear loads whose application sites do not correspond…

Q: A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive…

A: From the given problem, Positive Bending moment = 78kip f'c = 3200psi span  =26ft

Q: Determine the nominal bending strength of the beam section shown in the figure below. The overall…

A: fc = 49 MPa fy = 420MPa h(D) = 700mm d = 700 -80 = 620mm b = 200mm

Q: A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced…

A:

Q: Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter…

A:

Q: A reinforced concrete column contains longitudinal steel equal to 1 per cent of net cross-sectional…

A:

Q: Using the stress block, determine the ultimate moment of resistance of the section shown in Figure 2…

A:

Q: Determine the required tension steel area of the T beam with given properties below. Width of flange…

A:

Q: A doubly reinforced rectangular concrete beam has a width of 300 mm and an effective depth of 500…

A:

Q: Determine a) the stress in each of the steel bars, and b) the stress in the concrete.

A: Solution : Given data Load = 1000 kN C/S area of steel = 90mm^2 Modulus of elasticity for steel =…

Q: Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and…

A:

Q: A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with…

A: To find : depth of concrete stress block

Q: A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible…

A: Given data  Stress in tension  Stress in compression  Area of cross section  To find out…

Q: A rectangular beam has a width of 285 mm and an effective depth of 520 mm. It is reinforced with 4 –…

A:

Q: A rectangular reinforced concrete beam has a width of 300mm and an effective depth of 400mm.…

A:

Q: A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars,…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A rectangular beam has the dimensions (see Figure) b- 12 in, h- 20 in, and d- 17 in. and is…

A: It is required to determine the stress in the steel due to 10 ft-k moment.

Q: A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars.…

A:

Q: The concrete post is reinforced axially with four symmetrically placed steel bars, each of…

A:

Q: 6m-simply supported beam cross-section is show in the figure below is prestressed with 15 wires of…

A:

Q: The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile…

A: Given data- Maximum load P=200 kN=200×1000 NDepth d=150 mmlength L=300 mmTo Find-The split tensile…

Q: -kips.

A:

Q: A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced…

A: Given : Width of cross-section of cantilever beam, B = 250 mmEffective depth of cross-section of…

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all…

A: Given, fck = 22.00 MPa fy = 404 MPa Assuming, balanced section, xudlim=0.00350.0055+0.87fyEsFor,…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.