A log that is 0.6m in diameter is to be cut into a rectangular section for use as a simply supported beam. If the allowable bending stress for the wood is 70MPa, determine the largest P (kN) that can be supported if the width of the beam is 300mm. h 2.4 m- b -0.6 m- P 1 + -2.4 m

A log that is 0.6m in diameter is to be cut into a rectangular section for use as a simply supported beam. If the allowable bending stress for the wood is 70MPa, determine the largest P (kN) that can be supported if the width of the beam is 300mm. h 2.4 m- b -0.6 m- P 1 + -2.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa.…

A: Calculate the axial force in each of the segments of the given bar. Then using the algebraic sum of…

Q: Calculate the maximum allowable load (in kN) that a nominal 350mm x 350 mm sawn lumber column, 3.5m…

A: Solution-The given values are as follows,The column dimension=350×350The column…

Q: Compute for the Modulus of Elasticity of the Wood if the Clear Span Length is 2300 mm, applied load…

Q: The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa.…

Q: A timber beam shown in the figure is made up of Kamagong (50% stress grade). Use LRFD. All the given…

Q: Determine the maximum axial load P (in kN) that can be applied to the wood compression block shown…

A: in given block cross section area of block A=width×depth =200×120=24000 mm2let stress on vertical…

Q: 1.7 in 2.5 in 2.7 in T 0.755 in Three wood boards, each 4.3 in. wide, are joined by the…

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

Q: A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and…

Q: Problem 6.5 - Determine a) the magnitude and location of the resultant mijnímým mj of the…

Q: 75 /2 100 mm

Q: 4 KN 2 KN 10 KN

A: Solution

Q: When computing the crushing stress of a wood compression member, the column stability factor, Cp,…

Q: shear strength value is in wood parallel to the grain O a. medium O b. Maximun O C. least O d.…

Q: A timber beam shown in the figure is made up of Sasalit (50% stress grade). Use LRFD. All thegiven…

Q: 1) Use the notion of symmetry and construct an FBD for only the upper half of the left-hand wood…

A: Solution; Given that; β=74° P=1360 b=1.55 in. d=3.70⇒d/2=1.85 length of AB=1.85sinβ2LAB=…

Q: wood wood 250 mm

A: STRAIN IN STEEL= STRAIN IN WOOD εS=εWσSES=σWEWσS= Stress in steelσW= Stress in woodES=youngs modulus…

Q: How much load must be applied on the wood, with a clear span length of 2350mm, deflection of the…

A: Given:- The clear span length = 2350 mm The deflection of the wood = 12.5 mm The modulus of…

Q: • width of beam, b = 350 mm • thickness of beam, t = 450 mm • f'c = 20.7 MPa • fy = 415 MPa • steel…

A: Answer We need to find the ultimate moment on the beam. Ultimate Moment(Mu) will be equal to maximum…

Q: roblem eel and aluminum plates are used to reinforced an 80 mm by 150 mm timber eam. The three…

Q: GIVEN; Steel / wood composite beam with cross-section shown Mmax = 1.5 x 10° in-lb Estel = 30 x 10º…

A: Composite beam: The combination of one or more material used in the manufacturing throughout the…

Q: A beam will support a combination of dead, live, and earthquake loads. The Load Duration Factor for…

Q: 2. Obtain the interaction diagram for the column section whose dimensions and reinforcement are…

Q: Compute for the Modulus of Elasticity of the Wood if the Clear Span Length is 2300 mm, applied load…

A: step 1-

Q: ticity of the Wood if the Clear Span Length is 2300 mm, applied load is 10lbs and the deflection of…

Q: A cantilever wood beam with a span of L = 3.6 m supports a linearly distributed load with maximum…

Q: A structural joint is formed as shown in the figure with the wood members connected by 16d common…

A: Solution:- From Table of Lateral Load Capacity of Common Wire Nail, we read a value of 141 lb per a…

Q: For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m…

Q: Problem 6.108 The wood used for the T-beam has an allowable tensile and compressive stress of…

A: Given :

Q: 5. Given : Allowable bending stress of 12.5 MPa Allowable shearing stress of 0.45 Mpa Elasticity of…

Q: Two aluminum posts are located at equal distance from the middle steel post as shown. Take note that…

Q: A beam will support a combination of dead, live, and earthquake loads. The Load Duration Factor for…

Q: g) the maximum bending stress in timber. Enter your answer in MPa to 2 decimal places.

Q: 4. The two pieces of wood, 2 in. by 4 in., are glued together along the 40⁰ joint as shown in figure…

A: Area of wood pieces, AngleTo find: (A) Maximum load for wood strength of . (B)…

Q: A wood beam carries the loading shown in the figure, calculat mm from the top of the of the beam on…

Q: Two wooden members of (25*b) * (60*b)-mm? uniform rectangular cross section are joined by the simple…

A: Given, Cross section area = 175 mm x 420 mm Load P = 12 kN Ultimate tensile strength = 4 MPa…

Q: Compute for the Modulus of Elasticity of the Wood if the Clear Span Length is 2300 mm, applied load…

Q: determine the safe resisting moment of the beam in KN.M.

Question

A log that is 0.6m in diameter is to be
cut into a rectangular section for use
as a simply supported beam. If the
allowable bending stress for the
wood is 70MPa, determine the
largest P (kN) that can be supported
if the width of the beam is 300mm.
h
2.4 m
b
-0.6 m-
P
1
+
-2.4 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1080 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 4.2 kN. Use a = 18 mm and b = 144 mm. d Glue b P P Answer: d = i mm
Mechanics of Deformable Bodies L T The wooden bar consists of two segments, each of length L. One segment has a square cross section of width d, the cross section of the other segment is a circle of diameter d. The working stress for the wood is tw=5MPaand the shear modulus isG=0.5GPa. Using L=0.6m and d=50mm, determine (a) the largest torque T that can be safely applied; and (b)the corresponding angle of twist for the bar.
Please show your solution clearly thank you
show complete solutions and answer should be in 4 decimal places
4. Steel and aluminum plates are used to reinforced 100 x 175 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 130MPA Steel = 210MPA Aluminum = 90 MPa Aluminum = 80 MPa Wood = 20 MPa Wood = 15 MPa 30 mm CTEEL WOOD ww.skl A LUMINUM 140 mm
Two wood boards, each 15 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 995 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 5.6 kN. Use a = 21 mm and b = 168 mm. d Glue b P P a Answer: d = i mm
(a) Draw the shear and bending-moment diagrams for the beam and loading shown below. 48 kips 48 kips 48 kips B A E -6 ft- 2 ft' 2 ft 2 ft (b)If the cross-section of the beam is as shown below, determine the maximum tensile and compressive stresses. 8 in. 1 in. 1 in.- 6 in. 1 in. 4 in.