(Submit your answers on a separate sheet if necessary.) 1. If some of your unknown sample failed to dissolve completely, would the value of the molecular weight you calculated be too high, too low, or unaffected? Explain fully. 2. What would be the effect on the experimentally determined molecular weight if your sample contained a soluble impurity of higher molecular weight than the pure sample? Explain. . What would be the effect on the observed molecular weight if your unknown sample contained : insoluble impurity of lower molecular weigh than the pure sample? Explain.

(Submit your answers on a separate sheet if necessary.) 1. If some of your unknown sample failed to dissolve completely, would the value of the molecular weight you calculated be too high, too low, or unaffected? Explain fully. 2. What would be the effect on the experimentally determined molecular weight if your sample contained a soluble impurity of higher molecular weight than the pure sample? Explain. . What would be the effect on the observed molecular weight if your unknown sample contained : insoluble impurity of lower molecular weigh than the pure sample? Explain.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A student forgot to add the mass of the unknown solute in trial 1 to the mass of the solute that was weighed for trial 2 and then added to the cyclohexane-solute solution used in trial 1. How would this omission affect the calculated molecular weight of the solute?
You have an aqueous extract that has been dried and you are going to perform a liquid/liquid separation. You must use a mixture of two solvents: a. Which solvent mixture would you use? Available solvents: cyclohexane, chloroform, ethanol, methanol, hexane, acetone. b. What compounds would you expect to be in each phase?
Assume that your compound recrystallizes equally well from benzyl alcohol and isopropyl alcohol. Which solvent is the better choice for recrystallization? a. Benzyl alcohol because it is miscible with water. b. Isopropyl alcohol is better because it has a much lower boiling point and is easier evaporate off c. A mixed solvent - benzyl alcohol and isopropyl alcohol d. It doesn't matter which one if they work equally in the recrystallization process.
What would have been the effect on the formula weight you calculated for your unknown If the unknown was still bubbling when you filtered your product?
Briefly explain how you determined when the reaction was complete PROCEDURETo a six inch test tube was added thiamine hydrochloride (0.65 g), followed by water (2mL). The mixture was gently shaken until homogeneous, and then ethanol (7.5 mL)was added. Finally, sodium hydroxide (10%, 1.5 mL) was added and the mixture wasgently stirred to ensure complete mixing.Benzaldehyde (3.8 mL) was then added at room temperature in one portion with gentlestirring. The pH of the resulting reaction mixture was determined and adjusted to >10by dropwise addition of 10% sodium hydroxide. The reaction mixture was then partiallysubmerged in a 65 °C water bath2 and the progress of the reaction was periodicallymonitored by TLC analysis.Once TLC analysis indicated that the reaction was complete, the reaction mixture wascooled to approximately room temperature, and then chilled in an ice-water bath. Theresulting precipitate was collected by vacuum filtration and air-dried. The crude productwas purified by…
How would each of the following errors affect the experimental value of your molarity of acetic? Would your Molarity value be too high, too low, or unaffected? Explain your answer. if you titrated your acid sample to a bright pink rather than faint pink endpoint? if your "acetic acid" burette was still wet inside with deionized water when you filled it with acetic acid? if you recorded the final volume of NaOH as "39.88 mL" instead of "38.88 mL"?
Please help me answer these question 4. Does the pooling of results in this experiment yield an average % Mg in MgO, which is closer to the accepted value than your class average? 5. Compare the precision obtained by your class to the precision obtained by the composite of all classes. Discuss. 6. What conclusion can you draw from the analysis of the data in assessing whether this laboratory procedure gives accurate results?
1. Discuss the following: a) direct method of weighing b) indirect weighing using the analytical balance. 2. Explain how suction filtration is carried out in the laboratory. Give the important points that must be observed in doing the process. 3. Explain why it is important to wash the precipitate. Can distilled water be used to wash all types of precipitates? 4. Discuss how to use a desiccator. When should a desiccant be replaced? Give 2 examples of substances used as desiccant.
The compounds in a multi-component solution can be separated by extraction. By using the most appropriate solvent, all the amount of the target compound can be isolated. a First statement is true. Second statement is false. b First statement is true. Second statement is false. c Both statements are true. d Both statements are false.
please i need your help A particular extraction proceeds with a distribution coefficient of 6. The system consists of 3.5 g of compound X dissolved in 60 mL of water (solvent 1). The effectiveness of three 60-mL extractions with n-hexane (solvent 2) is compared with one 180-mL extraction with n-hexane. Questions: 1. How many grams of compound X will be recovered in n-hexane in the third extraction? 2. How many grams of compound X will be recovered in water in the third extraction? 3. How many grams of compound X will be recovered in -hexane in the first extraction? 4. How many grams of compound X will be recovered in water in the first extraction?
Hello, I do not understand this quiestion or how to do this problem. Can you help me so I can follow along. 7. 5.00 mL of stock solution is diluted to 25.00 mL, peoducing solution ALPHA. 10.00 mL of solution ALPHA is diluted to 25.00 mL resulting in solutin BETA. 10.00 mL of solutionBETA is then diluted 25.00 mL producing solution Gamma. a. Determine the dilution factor in produciing solution Alpha from the stock solution. b. Determine the dilution factor in producing solution Beta from the solution Alpha c. Determie the dilution factor in producing solution Gamma from the stock solution Beta. d. Determine the overall serial dilution factor in producing solution Gamma form the stock solution.
6. Explain how you might use precise BCA, glucose, and CUSO4 to solutions with a UV-visible spectrometer to measure [Cu-"] in a sample of water.