steel rod: 0 24 mm 0.4 m 3 m Figure 1.23 A rectangular column of sides 0.4m x 0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel = 200 GPa and Econcrete = 29 GPa. %3D %3D 0.35 m

steel rod: 0 24 mm 0.4 m 3 m Figure 1.23 A rectangular column of sides 0.4m x 0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel = 200 GPa and Econcrete = 29 GPa. %3D %3D 0.35 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. b Figure.4: Cross-section of a hollow-square steel column
A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the section M and the screwed section N, where the diameter at the root of the thread is 2. 4 mm as shown in Figure QI.2. (6) M - 40 kN 40 kN - 4 mm diameter 6 mm diameter Figure Q1.2: Steel bolt
2 3.0 m 175 KN 2.5 m 200 KN (1) (2) 46 mm 175 kN 30 mm Problem 3 A compound axial member consists of steel (E=200 GPa) segment (1) and brass (E=120 GPa) segment (2). a) Compute the total deformation of the compound member for the loading shown (in mm). b) Sketch an internal normal force diagram c) Calculate the average axial stress in segment 2
A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside diameter of 72mm. The spring has 16 active coils. If the permissible shear stress of the spring material is 345 N/mm2 and the Modulus of rigidity is 83 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, considering the effect of curvature. b) Calculate the value of axial load in N neglecting the effect of curvature.
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
Two round solid bars of different materials are connected in series against rigid supports as shown in Figure 4. Determine the stress in each bar and the support reactions if temperature is increased by 18° C. Bar A da, EA, A Bar B dв, Ев, ав LA LB Figure 4 Use the following information. Bar, B: Length, LB Diameter, dB Poisson's Ratio Young's Modulus EB = 210 kN/mm2 Coefficient of expansion aB = 12.4x106 °C- Bar, A: Length, LA Diameter, dA = 25mm =D40 mm = 10 mm 30 mm S. = 0.28 =D0.32 = 70 kN/mm² Coefficient of expansion aa = 16.5x10-6 °C-I Poisson's Ratio %3D Young's Modulus EA
1. The rigid beam ABC is supported by the pin joint at A and the steel wire BD. The wire is 0.10 inches in diameter and 90 inches long before the load is applied. Find the stress in the wire, the change in length of the wire when the load is applied, and the diameter of the wire under the load. Use E = 30 X 106 psi and v = 0.35. ܢܢܢܢܢܢ A 60 in 120 in D B C 750 lb
Aluminum A = 400 mm Bronze A = 200 mm Problem 2: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Steel A = 500 mm 2P 4P 2.5 m 2.0 m 1.5 m Show all
250 mm Q1: The beam shown in Figure 1 is subjected to a vertical force Py and a horizontal force Pr The data for P Pr, a L,and e are shown in Table1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv > 135 KN 55 omm a I=> 6omm Ph 2248KN 120 mm L =2 600mm Figure 1
As shown in the figure, a column has a 10-inch by 10-inch cross section. A compressive load P with magnitude of 250 lb is applied. Determine the compressive normal stress at the cross section “a” (fc). Calculate final stress values and units
1.2 Figure 1 show a compound bar made of the aluminum alloy with three different cross-sectional. The bar is subject to a tensile load of 40KN. Take E = 69 GPa, Determine the stress in each section and the total elongation of the bar 30 mm 40 mm 50 mm 40 kN 40 kN 0= 20 mm 0= 15 mm 0 = 10 mm