st al 2 m 0.75 m 0.75 m'0.75 m 0.75 m' pV 2P

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A: The maximum value of Pmax that can be supported by the structure is  128kN

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and…

A: Using similar triangle approach Here, the length and area of both of the rods are the same.

Q: The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is…

A:

Q: A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads.…

A:

Q: The solid circular rod has a cross-sectional area of 450 mm2. It is subjected to a uniform axial…

A:

Q: Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of…

A:

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial…

A:

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm  the bar thickness (t) = 15 mm. Each…

Q: The solid circular rod has a cross-sectional area of 310 mm². It is subjected to a uniform axial…

A:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

A:

Q: The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial…

A: To Find : the normal stress in the rod at x=0.5m Given :  cross sectional area of rod A=410mm2…

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

A:

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm. Determine the average…

A:

Q: The singular force F will be applied to the beam with a hollow rectangular cross section.…

A:

Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,…

A: Given data: Permissible screw stress,σtper=150MPa Permissible bearing stress for wood, σbper=28MPa

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A:

Q: The solid circular rod has a cross-sectional area of 450 mm2. It is subjected to a uniform axial…

A:

Q: The solid circular rod has a cross-sectional area of 420 mm². It is subjected to a uniform axial…

A:

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

A:

Q: The solid circular rod has a cross-sectional area of 350 mm². It is subjected to a uniform axial…

A:

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

A:

Q: The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is…

A: The diameter of pin, d  = 19 mmThe bar width, b = 70 mmThe thickness, t = 15 mmThe average shear…

Q: The rectangular bar is connected to the support bracket with a 14-mm-diameter pin. The bar width is…

A:

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

A:

Q: The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm.…

A:

Q: 4. Determine the maximum normal stress developed in a bar when it is subjected to an axial load of P…

A:

Q: The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is…

A:

Q: Answer: Pmax i kN

A:

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

A: Solution.jpg

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.