Solve the given truss problem and find out member stresses using FEM. 1000 kN 3000 kN B D MATHalling.com 60 60° 60° 60° A 10 10' 4000 kN mm.onilsHTAM MATHalino.com

Q: roblem#4: An object with a mass of 75 kg floating on water is pulled py a neters, calculate the net…

A:

Q: Given the balanced Azimuths for the 4 sided traverse below, calculate the new internal angles.…

A:

Q: Determine the vertical reaction at B for the beam shown.

A:

Q: Consider the following simply supported beam with a concentrated dead load acting at a distance of 6…

A: Given,  L=18ft X=6ft Dead load = 38k Uniform live load = 2.7k/ft n=8 fc'=3000psi Our aim is to…

Q: Calculate the magnitude of the resultant vector given the diagram below and the following table of…

A: From figure:Fx=F1cosθ1-F2cosθ2+F3cosθ3Fy=F1sinθ1+F2sinθ2-F3sinθ3ResultantFR=Fxi+Fyj

Q: Calculate the cumulative percent

A: Sieve weight retained percentage weight retained cumulative percentage 4.75mm 31.5 5.92% 5.92…

Q: RATE WILL BE GIVEN

A: Given- The three linear sides of a land and the ordinates along fourth curved boundary. Required- To…

Q: Show in calculation the project status if it is behind, ahead, or on schedule: 10K A AA 11K 12K 10K

A:

Q: Calculate the contract value, the monthly value of the planned work to be completed (Budget value)…

A:

Q: When preparing an accident report, what classification of Cause Analysis would you consider “how…

A: Whenever addressing work-related accidents, one could determine the extent of the problem by…

Q: In your own words, briefly discuss the safe design theorem and its implications for the structural…

A: The Safe Design Theorem is a mathematical theorem that states that the total load on a structure…

Q: the cost object for a project.

A:

Q: 4. The two vertical rods attached to the rigid bar are identical except for the length. The bar is…

A:

Q: F= 750 N 'F2 |35°

A: solution  given that  resultant force is directed horizontally means we can conclude that  the sum…

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: 3. A homogeneous bar with a cross-sectional area of 400 mm² is attached to fixed supports as shown…

A:

Q: 40 mm 30 m 13 rom 24 j 24 jam 27 Determine the moments of inertia I, and I, of the area shown with…

A:

Q: 27 Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A:

Q: A 5 cm diameter shaft is reduced to a diameter of 2.5 cm and subjected to a torque of 200 N-m. It is…

A: Solution: Given Data: Diameter of the shaft, D= cmChange in diameter, δd=2.5 cmTorque, T=200…

Q: The absolute maximum shear for the girder below will be at point A в F 5 @ 4 m = 20 m O NON OF THEM…

A: Given data Beam End conditions  Span length

Q: 1) A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi…

A:

Q: A traverse is a series of consecutive lines whose ends have been marked in the field, and whose…

A: A traverse is a series of consecutive lines whose ends have been marked in the field, and whose…

Q: Compute the immediate deflections due to dead load and live load on the beam of the figure for…

A:

Q: Determine the unknown distance in the loaded cable. 1.5 m 1.5m 0.5m B. C.

A: Determine the unknown distance y in the loaded cable.

Q: Determining the locations of points and orientation of lines frequently depends on the observation…

A: Determining the locations of points and orientation of lines frequently depends on the observation…

Q: 2.87 m 2.87 m 17.00 kN 17.00, kN 14.00KN/m Toucere to eet I I 4.10 m 4.10 m

A:

Q: Calculate the resultant force vector using the table and diagram below. Round your answers to 1…

A:

Q: The result of the liquid limit tests where N is the no of blows and w is the water content in % are…

A:

Q: r is designed to ca 20KN. Using allow 20MPa and ỢC = 6

A:

Q: x 105 and in in. Determine Iy: Answer is in Just answer the blank space in 4 decimals 12 in 20 in

A:

Q: The is a schedule forecast of the probable duration of a project.

A: Given data Schedules forcast Probable duration of project

Q: PLEASE KINDLY CHECK IF THIS IS CORRECT! RATE WILL BE GIVEN

A:

Q: 5. The rigid bar is supported by a smooth pin and two rods as shown. Neglect the weight of the rigid…

A:

Q: The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is hinged at A. Determine the…

A:

Q: Problem 1. The tension member is a PL 6 x 1/2. It is connected to a 3/8-inch-thick gusset plate with…

A: Answer Given in the Below attachments

Q: The length and width of panels used for interior doors (in inches) are denoted as X and Y,…

A:

Q: Problem B Equipment Estimating Use the following information for a scraper. Actual cost (delivered)…

A: Actual cost of vehicle= $162000 Useful life = 6*1400= 8400 hrs Life of tires = 3500 hrs  No of tire…

Q: There are 3 ways to protect against trenching hazards. Which one of the following is not a method? O…

A: Trenching is technique of excavtion in ground . The depth of excavation is deeper than its width .…

Q: Determine the moment of the 3.6 kN force about point A? (Round your answer to the nearest tenth and…

A: M=Force ×Perpendicular distanceMoment of 3.6kN about A is

Q: largest uniformly distributed load that can be applied over the right two-thirds of the beam if the…

A: ΣMR1=0 3R2=2w(2) R2=4/3w  ΣMR2=0 3R1=2w(1) R1=2/3w  (fb)max = Mc/I Where,        (fb)max = 60MPa…

Q: rod. Answer: PA = 239 kN B A 6 m 6 m 5 m 4 m +2 m→ 600 kN

A:

Q: 5. The composite bar, composed of aluminum and steel bars, is firmly attached to rigid supports. An…

A:

Q: 60 kN A 30% 2000 mm 3000 mm 30 kN 50 KN 3000 mm 50 kNm

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.