snown Iin vable shear stres al is 145 MPa. If s about 6 mm, wh ad that can be an

Q: H.w Find max. tensile and comporsive stresses. 5 KNim 5KN 60 2. m A B. 120 ww

A: A simply supported beam is a loaded beam that is hinged at two points on the length of the beam. To…

Q: 200 MPa T If the element rotate clockwise by 30 deg. Find the stress -350 MPa a. -136.6 MPa O b.…

A: If the element rotate clockwise by 30 deg. To Find-  The Txy' stress,

Q: EXAMPLE 4-3 Isothermal Compression of an Ideal Gas A piston-cylinder device initially contains 0.4…

A:

Q: Please use maximum shear stress theory

A:

Q: 3. The pruning mechanism of a pole saw is shown as it cuts a branch S. For the particular position…

A:

Q: he answer in M1 is 4283.29lb, can you show me how to get this answer

A:

Q: What will be the occerelalion at point L if theuniform KL bor is left horigontal. 2m Support…

A: Given, The mass of the bar, m=25 kg The length of the bar, L=4 m

Q: An ideal Carnot heat pump operates from a low temperature reservoir T₁-272.6 K and supplies 9.94 kW…

A:

Q: Consider the circular bent rod with điameter 20 mm. The free-end of the bend is subjected to loads…

A: The horizontal force of 400 Newton will generate a bending moment at the section b-b. The vertical…

Q: [No.6] Consider a double-fluid manometer as shown in the figure, attached to an air tank. If one…

A:

Q: Problem 3 and no sign) produced by the applied forces about point C. Prepare an FBD to determine the…

A:

Q: 2m 4m E 4m r 4200 kN MN/ ARea = bh b= 0.5m Stress = 100 StRess in members BD, cD and CE

A:

Q: The device shown is a part of an automobile seat-back-release mechanism. The part is subjected to…

A: Given data as per question Force =5.6 KN Angle =280   Drawing FBD of the system…

Q: Hi, the diameter is 10 mm in my problem, not 15 mm.

A:

Q: 8 ksi 4 ksi 12 ksi

A: From the given figrue, σx = -12 ksi σy = -8 ksi τxy = 4 ksi

Q: Show complete solution

A:

Q: 2. Determine the forces in members BC and FG of the loaded symmetrical truss. Show that this…

A:

Q: I can't seem to find the shear stress at point b. Here's my work for reference.

A: Given-Information: L1=32ftL2=9.3ftL3=14.4ftp=13.5lb/ft2do=9.5int=0.31in To-Determine: Stress at B,…

Q: Determine the reactions for the loaded beam as shown below. Neglect the weight of the beam. 120 lb…

A:

Q: Calculate the normal and shear stress at points "a, b and c"

A: There are two types of stresses caused in a beam due to its lateral loading which are- 1. Normal…

Q: 4MPA 12MPA 12MPA

A:

Q: why do you multiply by 16 in the shear stress?

A: This question is based on the concept of Torsion equation.

Q: Since both the force that cause Bearing Stress to Normal Stress is perpendicular to the cross…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: How do i determine the shear diameter of a shear pin made from 0.20C cold drawn mild steel using…

A: Given: The material is 0.20C cold drawn mild steel. And the tensile yield strength of the 0.20C cold…

Q: 1025 steel hold firmly 60 °C, there is a long It is heated from 20 c to Assume from both ends.…

A: Heat transfer is the form of energy that transfers from one system to another system by virtue of…

Q: Determine maximum shear stress . Please me . Thanks for the help

A: To determine the maximum shear stress for the stress element

Q: A steel bar with triangular cross section has a base 30 mm and height 20 mm. When 1.2kN force…

A: Stress developed in the bar  = Force applied/area of Cross section.

Q: . STRESS. Find the vertical stress at a depth of 1,800m with an average relative density of 2.5

A: Given:Depth, h=1800 mAverage relative density, s=2.5

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in ension. An axial load…

A:

Q: A- ODD: A 2.0 kN bar AB carries a load F = 75 kN vertical force at A. The bar is supported by a pin…

A:

Q: Explain the effect of shear stress on body in following figure?

A: If the load applied is parallel to the resisting area the stress induced in the material is known as…

Q: What is shear strength & how is it calculated?

A: There are no standard values published in the books for the shear strength. In some cases we take 60…

Q: Using same question find the principal stress using mohrs circle

A: We will use Mohr's circle to find principal stress.

Q: a: What is the magnitude of the maximum shear stress in MPa? b: What is the magnitude of the…

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the…

Q: 2.2 in. in.- A IB = in. 1.6 in. e maximum and average stresses in sections A and B, take t = 0.45 in

A: Stress concentration is defined as the localization of high stresses due to the irregularities…

Q: Copied or wrong solution get multiple downvote for sure. 1)A cylinder with a 0.3 m inner diameter…

A:

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A: Given:Elevation difference between the lake and the reservoir, ∆z=25 mWater flow rate, Q=25…

Q: Compute the magnitude of the moment Mo of the 345-lb force about the axis 0-O. Assume F = 345 lb, d…

A: Given data as per question Force =345 lb d=16 in H =11.6 in h =6 in…

Q: Q1. For the beam and loading shown, (a) draw the shear and bending- moment diagrams, (b) determine…

A:

Q: Q3B) A metal is fabricated by drawing at 125 °C. The metal melting temperature is 400 °C. Find by…

A: Given dataFabricated Temperature (T)   (a) Working Temperature=125°CMelting Temperature=400°C Tm

Q: The steel pipe AB has a 72mm outer diameter and a 5mm wall thickness. Knowing that the arm CDE is…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.