[No.6] Consider a double-fluid manometer as shown in the figure, attached to an air tank. If one fluid is mercury, determine the density of the other fluid for the given pressure. Take Patm= 100 kPa.

Q: *3-44. Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle.

A:

Q: TOPIC: TORSION I. Write ALWAYS TRUE if Hhe At ate ment ia true for all Rtuation 2f not , Write F…

A:

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: Figure 8-4 Full Alternative Text 8-5. The gas storage tank is fabricated by bolting together two…

A: As per Expert Guidelines we are supposed to answer only the first question of the given multiple…

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A:

Q: Shown above is a cord tension tester. Find the tension T in the cord, expressing it in terms of the…

A: The tension in the cord is 4Pcot 10

Q: D C. - 4 ft 4 ft t- 3000 lb 100O Ib B y A K 4 ft - Determine the magnitude of the force (in Ibs) in…

A: GIVEN: W1=3000lbW2=1000lb

Q: Two horizontal metal plates each 30 mm thick are assembled by means of M25 bolt, a nut and washer.…

A: Sectional front view of plates with bolt, nut and washer.

Q: you! A round vertical steel tank has an inside diameter of 3 m and is 6.5 m in height. It contains…

A: Given:d=3 mh=6.5 mρ=850 Kg/m3σallow=25 MPa

Q: Part A, B, C Solved below,  asking solution for part D, E, F, G

A: In case of determining shear force and bending moment for the beams with udl or uvl, it is advisable…

Q: 100 KN 20 KN/m 10 m need NF, SF and BM diagram ? detailed answer in a basic way

A: It is required draw NF,SF AND BM Diagram

Q: Introduction to stress analysis Problem: Calculate the critical design loads applied to the piston…

A: Piston is a reciprocating part of an internal combustion engine which reciprocate with in the…

Q: 1- Design and sketch the form for 7.5 ft high and 1 ft thick wall using 5/8" B-B plyform Class I (4…

A: Given:- h=7.5 ftt=1 ft5/8" B-B plyform Class I (4 ft x 8 ft sheets)2 x 4 s4s Douglas Fir Larch No.2…

Q: 4. A packaging machine mechanism has a link with a square cross section of 0.50 in on a side. It is…

A:

Q: A Hgally applied force. If the mass moment of inertia of the %3D the radius of the cylinder. Answer:…

A:

Q: The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft.…

A:

Q: Assignment 2 E 松 A B S KN 5kN SkN Calculate Porces ih each Amen ber of truss, Use method of jochts.

A:

Q: Draw shear force and bending momenE

A:

Q: Calculate the minimum wall thickness (in) for a cylindrical vessel that is to carry a gas at a…

A: Pressure(P)=1766 psiDiameter,d=2 ftLimited stress,To determine:Minimum wall thickness(t)

Q: 2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset…

A: (a) To find: The bearing stress between the strut and the pin in MPa. Given: The compressive load is…

Q: Determine stress

A: given - F=3N Cross section area= 4mm2 Need to find Stress

Q: 8 3. Which is the correct Design expression in the case of tension(compression)? (1 Puan) max o, =…

A: Given Data⇒ Design expression Compression Tension

Q: Compute the maximum tensile and compression Stresser developed in the beam that is loaded and has…

A:

Q: Exd:Design the (T-beam) section have the properties: by =1200mm , hy = 150mm, d = 500mm, b,, = 300mm…

A:

Q: Compute the resultant force acting on the pin at C (in kN).

A:

Q: 5. Find 2 in 口2 im 300 lb-ft cosS - Section V80 lb it =33.9 psi Tonia Ob -b =8.48 psi TL-b= 147 Psi…

A: Let us consider tension force in inclined member is P. Drawing FBD of horizontal member:

Q: Rod BD is made of steel (E= 29 x 106 psi) and is used to brace the axially compressed member ABC.…

A:

Q: A2.2 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: here's a comprehensive explanation of why a bar magnet suspended on a string aligns itself with the…

Q: concept checkpoints Compute the resultant force acting on the pin at C (in kN). A 500.00 mm 60 kN kN

A: Given Data The total heigth of the bar is:h=1500 mm The width is:b=900 mm To find: The resultant…

Q: Question 1 a) Figure Q1a shows a bracket that can roll and move horizontally along a beam. A 1600 N…

A: Any action that can change the state of motion is known as force. Force is described by its…

Q: The maximum pressure of air in a 20-in cylinder (double-acting air compressor) is 125 psig. What…

A: Given data: P=125 psigN=1.75T=1000°F Need to determine the diameter of the piston rod.

Q: /C/Compute the collapse-pressure ratings Jor(1. 5-ir ubjected to(1000000 lbf) axial tension and…

A:

Q: Write the Shear strain max formula for Torsion?

A: To calculate the maximum shear strain value for torsion we must take into account the torsion…

Q: Explain the effect of shear stress on body in following figure?

A: If the load applied is parallel to the resisting area the stress induced in the material is known as…

Q: 1 Demi e ARCndD

A:

Q: 2.5m 18KN 3.0m 6KN/m 5.0m

A: given; lets take reaction force at point A=RAlets take reaction force at point…

Q: Given data: Force on box=12.6 N Displacement=3 m Find work done

A: Given data : Force on box=F Displacement=d   Required : Work done

Q: 60 k 30 kN DRaW the shean and mament Im diagram awith complete soktior

A:

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.