1- Design and sketch the form for 7.5 ft high and 1 ft thick wall using 5/8" B-B plyform Class I (4 ft x 8 ft sheets) and 2 x 4 54S Douglas Fir Larch No. 2 for studs and wales. Form will be used only once. The plan is to complete the placement in 45 minutes and the concrete weighs 150 pcf. Temperature at placement will not be lower than 65°

1- Design and sketch the form for 7.5 ft high and 1 ft thick wall using 5/8" B-B plyform Class I (4 ft x 8 ft sheets) and 2 x 4 54S Douglas Fir Larch No. 2 for studs and wales. Form will be used only once. The plan is to complete the placement in 45 minutes and the concrete weighs 150 pcf. Temperature at placement will not be lower than 65°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the minimum thickness of a normal weight concrete cantilever slab with length of 2.96 m and steel yield strength of 356 MPa?
Department: Mechanical Engineering MENG 222 – Strength of Materials PLEASE solve it very very quickly ?? ¶Draw neat, labelled diagrams. ¶Write relevant equations. ¶Be clear and specific and include units in answers. All thank and appreciation ?? ?
Design engineers in many situations must justify their selection of beams and pin-ended columns used in various machines. Your role in a mechanical design company that manufactures gearbox and gearbox mounting platform is to analyses the rolled steel beams and columns under study. Your manager asked you to properly select one rolled steel beam and one rolled steel column for the design and to provide your justification of this selection, if the following design requirements are given: Beams and columns are made of ASTM-A709/Grade 345 Factor of Safety (F.S) is 1.4 Buckling Euler conditions must be met. Beams are subjected to 50 kN axial force. Beam (A) has radius of 10 mm. Beam (B) has radius of 5 mm. Column (A) is subjected to 15 kN axial force. Column (A) has length of 1.5 m and radius of 10 mm. Column (B) is subjected to 15 kN axial force. Column (B) has length of 1.5 m and radius of 13 mm. Note: Column critical load must be determined (based on Euler theory caleulations must be…
Problem 3: Design engineers in many situations must justify their selection of beams and pin-ended columns used in various machines. Your role in a mechanical design company that manufactures gearbox and gearbox mounting platform is to analyse the rolled steel beams and columns under study. Your manager asked you to properly select one rolled steel beam and one rolled steel column for the design and to provide your justification of this selection, if the following design requirements are given: - Beams and columns are made of ASTM-A709/Grade-345 Factor of Safety (F.S) is 1.2 Buckling Euler conditions must be met. Beams are subjected to 50 kN axial force. Beam (A) has radius of 10 mm. Beam (B) has radius of 5 mm. Column (A) is subjected to 15 kN axial force. Column (A) has length of 1.5 m and radius of 10 mm. Column (B) is subjected to 15 kN axial force. Column (B) has length of 1.5 m and radius of 13 mm. P P A B Figure.3: Rolled steel beams. P P A P P Id B Figure.4: Rolled steel…
Only mechanical engineering experts can do best. Subject deformable
Fundamental Problem 9.7 Figure <1 of 1 Part A Locate the centroid of the wire bent in the shape shown. Take z=390 mm. y = 780 mm, z=520 mm. (Figure 1) Express your answer to three significant figures and include the appropriate units. Value Submit Request Answer Part B ÿ- Value Submit Units Request Answer Locate the centroid of the wire bent in the shape shown. = 390 mm, y = 780 mm, z = 520 mm. Express your answer to three significant figures and include the appropriate units. 1 of 4 ? Units Review
A post of No. 2 grade hemlock is 6.0 ft long and has a square cross section with side dimensions of 3.50 in. How much would n be shortened when if is loaded in compression up to its allowable load parallel to the grain?
please help solve and explain and include FBD please
Please complete this question ASAP. This question doesn't have a diagram and I keep getting stuck. I need this done within an hour and a half. Thanks.
A 2x4 stud wall with a 3 1/2 in. polyurethane foam cavity insulation, 1/2 inch of gypsum wall board on the inside and 1/2 in. of osb sheathing, a 1/2 in air space and 1/2 in of solid wood siding on the exterior .( Neglect presence of the studs)
Learning Goal: To analyze two built-up members that have the same geometry but are fastened differently, determine the maximum applicable shear force on each cross section, and determine the adjustment in spacing between the weaker member's fasteners that would allow the member to support the equivalent maximum shear force of the stronger member. The two cross sections shown below, (a) and (b), are subjected to a vertical shear force as shown. The members are fastened by nails that can support a load of 22.00 kN each and are spaced perpendicularly to the page in increments of s = 125.0 mm. The geometries of the cross sections are given by a = 235.0 mm, b = 50.00 mm, c = 225.0 mm, d = 135 mm, and e = 275 mm. Assume the cross sections are uniform along the entire lengths of the members. bk (a) Part A - Maximum applicable shear force on the member (a) *ak b 17 b ➜bk ➜bk Determine the maximum applicable shear force on the member (a). Express your answer to four significant figures and…
Problem 1: For the truss under the following 3 loading conditions, determine the minimum cost of each truss based on the following: Wood (popsicle sticks) - $100/stick • Cable (thread) - $10/section Please note that all members of the truss are the same length. Given this information, it doesn't matter what length you use, or what "X" is, but if it helps, just make up numbers, i.e. length of 5" and X of 10lbs. In class we will be using members that are approximately 6" long and weights that are approximately % Ib, although on the weights we can just add more to get the desired effect. Come to class with design in hand prepared to assemble the 3 different trusses to test with loads. A) x (lbs) B) x (lbs) x (lbs) x (Ibs) C) x (Ibs) 2x (Ibs)