2m 4m E 4m r 4200 kN MN/ ARea = bh b= 0.5m Stress = 100 StRess in members BD, cD and CE

Q: A short rectangular post supports a compressive load of P = 44 kN. A top view of the post showing…

A:

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear…

Q: 1) In the figure which shows a beam, its loading, and its rectangular cross-section, determine (a)…

A:

Q: Calculate the maximum and minimum normal stresses experienced by the lever indicated in the image.

A: lever as shown below

Q: Find the principle stresses at A and maximum shear stress.

A:

Q: Find the stresss in the left rod after its lower end is attached to the support.

A:

Q: PROBLEM#4 WRITE SHEAR AND MOMENT EQUATIONS FOR THE BEAMS IN THE FOLLOWING FIGURE IN EACH SEGMENT,…

A:

Q: Can you calculate the stress for the remaining point instead of point 1 only?

A: Given: To find: State of stress at remaining points

Q: Find normal and shearing stresses at point A .

A: For the Normal Stress at pt.A (considering the maximum stress condition) Normal Stress, σx = PA…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37-5mm…

A: Find the value of force Q and stress at point C and D

Q: Compute the maximum shear stress (r7maz) that this solid can have. Hint: Problem 3 Use the Mohr's…

A: For solution refer below images.

Q: 10 95 MPa 10 cm 5 cm

A: To Find : Maximum Stress in Plate =?

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…

A:

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: X 35 kPa 40 kPa 95 kPa

A: As stated in question, Stress along x-direction = σx = -95 kPa Stress along y-direction = σy = -35…

Q: Find strain

A: Given data : Original length L=100 mm Change in length ∆L=0.15 mm   To find : Strain

Q: 60 MPa 30 MPa 45 MPa

A: On the given element, Stress in x direction = σx = 45 MPa Stress in y direction = σy =  -60 MPa…

Q: find the internal forces, show all steps please

A: Hi,    As per the guidelines, we can only provide typed solution. Therefore, here we are providing a…

Q: A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not…

A: d=25mmTo be determined1. Find the force, F, on the 125 mm diameter sprockets.2. Construct the…

Q: Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a…

A:

Q: A- ODD: A 2.0 kN bar AB carries a load F = 75 kN vertical force at A. The bar is supported by a pin…

A:

Q: Find the stress if 1002 lb force applied on 12 in2

A: Given data : Force=P Cross sectional area=A   To find : Stress

Q: Find the stress in each segment and the displacement

A: Given the segment diameter, length and loading values.  Required: Stresses in each segment and…

Q: 8 KN 300 mm AY loe 4m 300 200

A: Given,

Q: In a stressed element, the value of normal stress along 'X' and 'Y' directions are 100 MPa (tensile)…

A: As shear stress is zero,

Q: element, th X' and 'Y' c 125 МРа (te ss is acting 5, if the pos axis.

A: Given in the problem we have let us draw the stressed element

Q: 1/2 30 (a) 60 1/23/ P +1/2 30 (b) Pix Rx- R₁ y 30 30 60 P b

A: Draw the free-body diagram of the given beam.

Q: Find the principle stresses at A if diameter is 1 inch.

A:

Q: dAB=1 in 12 in 5000 lb dec=0.5 in dcp=1 in Gap = 0.0150 in rope Con only their Damples or pool data…

A: Given: dAB=1 indBC=0.5 indCD=1 inlAB=12 inlBC=8 inlCD=8 in

Q: y O X 35 kPa 40 kPa 95 kPa

A: As given in question, Stress along x-direction = σx = -95 kPa Stress along y-direction = σy = -35…

Q: Find the cross sectional area if applied force is 26 N and stress produced is 60 N/mm2

A: Given data : Applied force F=26 N Stress produced σ=60 N/mm2   To find : Cross sectional area