3. A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 5kN. Find the minimum factor of safety using Maximum shear stress theory. All dimensions are in mm. -500 25 D. 7 +20 -35 D. -180 -3 R. -280- -175- -50 D. -25 D. -20

Q: Q4/ The corner of a 0.4m_ 0.3m 9.2 m cubic element is displaced to point C, whose coordinates are…

A:

Q: on as possible

A: given:σ1=100mpaσ2=100mpaσ3=0mpa

Q: What are the general equations of plane stress transformation?

A:

Q: With a suitable example explain the difference between True stress-strain and Engineering stress-…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: What do you mean by fatigue failure of machine parts? Explain briefly. Give an example of a thing or…

A: Fatigue Failure

Q: A rod of length 1.6m long has a diameter of 0.5m wide. this rode is made of 52100 chromium steel…

A:

Q: Define different types of stresses, strains and material constants.

A:

Q: Define the term lateral normal strain.

A: Strain is defined as the ratio of change in length upon original length .   Strain are of two type :…

Q: 2 (d) shows a typical aluminum stress-strain curve. A mechanical engineer has to carry out a tensile…

A: To design the appropriate rod. Given:σallow=400 MPaF=20 KNL=380 cm∆L=0.8 cm

Q: Explain the differences between a ductile material and brittle material. Also, draw their…

A: DUCTILE MATERIALS: 1. Ductile material are those which undergoes large plastic deformation under the…

Q: 2.20. The uniaxial yield strength of annealed AISI 1015 steel is 386 MPa. Estimate the shear stress…

A: Given data: It is required to determine the shear stress according to the Tresca’s theory and…

Q: Explain the difference between normal stress and shear stress?

A:

Q: How can we apply the general equations of plane stress transformation?

A: An object is under a biaxial state of stress when the stress exists only inside the 2-dimensional…

Q: Uniform and non uniform stress, gives proper solution explanation with diagrams.

A: Given data Uniform and non uniform stress, gives proper solution explanation with diagrams.

Q: Consider the same circular plate, as in the previous question, and consider a plate thickness of…

A:

Q: Using analytical method of transformation equations; (a) The orientation of principal planes and the…

A: Given Data: The stress acting in the horizontal direction is, σx=2R MPa. The stress acting in the…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Now we have the moment equation asMx=16×510-11×230=5630kN.mm=5.63kN.mMy=-20×510=-10200 kN.mm=-10.2…

Q: Explain the principle of stress and

A: Principal stresses are maximum and minimum value of normal stresses on a plane (when rotated through…

Q: 3. Explain the concept and the relationship between state of stress at a point and transformation of…

A:

Q: Describe the Maximum Normal Stress Theory?

A: The Maximum Stress Theory is one of the failure theories postulated by Rankine. Hence this theory is…

Q: Besides normal tensile stress, list three other types of material stresses?  Are these typically all…

A: Stress: Stress is defined as the internal resistance per unit area of cross-section. There are…

Q: Explain the deconvolution of the principal stress state into the hydrostatic and deviatoric stress…

A:

Q: Your boss is convinced and decided that the customers will save a lot of energy in processing…

A: This question is based on scientific opinion.

Q: Explain in detail c the soil layer. Use

A: At a point inside a soil mass, stresses will be created as a result of the soil lying over the…

Q: Define the term stress trajectory?

A: Stress Trajectory: It is the line continuously showing the changes in orientation of principal…

Q: A socket of above knee amputee is used in the following analysis. It may considered as cylinder with…

A:

Q: What is Shear Stress and explain with example?

A:

Q: the shear yield stress

A: Given; The uniaxial yield stress of a material is=300 MPa Acc. to Von Mises criterion,  Determine…

Q: One of the applications related to strain energy is Bow and arrow Explain how this is related to the…

A: Strain energy is the energy stored in a member due to deformation. It is the energy absorbed by a…

Q: Discuss the engineering applications of thermal stresses.

A: Thermal stress: The stress induced in any object due to the change in its temperature is known as…

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Q: Part-A (Theoretical & Mathematical Problem) For the following state of stress, (a) using the general…

A: (a) Write the given stresses from the diagram.   σx=20 ksiσy=-10 ksiτxy=-12 ksi   Write the angle…

Q: With a suitable example explain the difference between True stress-strain and Engineering…

A:

Q: Using Mohr's circle (no credits otherwise), solve the following questions: (a) the principal…

A: Do the following steps in order to draw the Mohr's circle for the given state of stress. 1. Draw two…

Q: A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During…

A: Given data: Tensile Force = 10000 N Initial Diameter of Cylinder = 2 cm Final Diameter of Cylinder =…

Q: Explain the term ‘Variation/transformation’ of plane stress.

A: Stress is a measure of the internal forces in a body between its particles on the plane of…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.