SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25 350 16 mm o 30 25 350 12. Compute for the gross area of the cross section. a. 28 000 mm? C. 23 490 mm? b. 29750 mm² d. 23000 mm? 13. Compute for the allowable tensile capacity due to yielding. a. 4698.00 kN C. 4610.78 kN b. 4654.39 kN d. 6706.59 kN 14. Compute for effective net area if shear lag factor is 0.90. Diameter of holes is 3mm more than that of bolts. b. 29750 mm? d. 23000 mm? a. 28 000 mm? C. 23 490 mm?

SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25 350 16 mm o 30 25 350 12. Compute for the gross area of the cross section. a. 28 000 mm? C. 23 490 mm? b. 29750 mm² d. 23000 mm? 13. Compute for the allowable tensile capacity due to yielding. a. 4698.00 kN C. 4610.78 kN b. 4654.39 kN d. 6706.59 kN 14. Compute for effective net area if shear lag factor is 0.90. Diameter of holes is 3mm more than that of bolts. b. 29750 mm? d. 23000 mm? a. 28 000 mm? C. 23 490 mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q// A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm', determine the stress in each section. 4P Steel Bronze Aluminum P 609.6 mm 914.4 mm 762 mm
Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of elasticity E=200 GPa, cross sectional area A=500 mm2. Determine the ww normal stress in each bar due to load P. a a=280mm b=70mm C=1177mm L=1075mm P=775mm L E B D F
A tension member in a roof truss is composed of two ASTM A36 structural steel angles that together have a net cross-sectional area of 5.66 in?. Compute the allowable total load if the allowable tensile stress is 25,000 psi. O a. 189.64 kips O b. 141.50 kips O. 137.16 kips O d. 220.25 kips
determine the tensile stress in each segment of the bar shown. Segment AB cross section 2in x 2in. Segment BC has a circular cross-section with a diameter of 1.75 in . The tensile load P= 75 kips
Consider the truss shown in (Figure 1). Suppose that F = 30 kN Figure A 3m 3m < 1 of 1 ▼ Determine the force in the member CD of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case tension. FCD- Value Submit Part B HA Part C Request Answer Determine the force in the member CB of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCB- Value Submit Request Answer HÀ Submit Part D FDA- Value HA Determine the force in the member DA of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive…
F (kN)=36 L1 (m)= 37.0053 Eal (GPa)=74
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
2. Determine the normal stress in members DF, GH, and GI in the truss shown. The cross- sectional area of each member is 900 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 5 kN A 2 kN B 3 kN C F H K 2 m 2m 2 m
The support in Figure 14.21a is to be constructed from a 4340 steel plate tempered at 800◦F. The yield strength of the steel is 228 ksi, and; its value of KIc is 51 ksi√ (in.). The width of the support, w, is 4 in.; the length, L, is 36 in.; and the thickness, t, is 0.25 in. Figure 14.21b gives f(a/w) in the equation σ = KIc/[f(a/w) √ (πa)]. A. If the crack length, a, is small enough, the support will yield before it fractures? What is the size of the largest crack for which this is true (i.e., what is the largest value of a for which general yielding will precede fracture)? Assume that any fracture would be in mode I (plane strain). Discuss critically the assumption of mode I. B. If it is guaranteed that there are no cracks longer than a length equal to 80% of that in Figure 14.21a, does this assure that failure will occur by yielding, rather than fracture? Explain briefly.
Q3
The bolt in (Figure 1) is fixed to its support at C. Figure B in. A 6 in