Situation 2: A W10x30 has a length of 4.80 m. Fy= 248 MPa. The properties are given below. Properties of W shape A - 5,700 mm^2 d-267 mm bf - 148 mm tf - 13 mm kdes - 7.62 mm tw - 14.5 mm rx-111 mm ry-34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are pinned? 311 KN 281 KN O 340 KN O 392 KN

Situation 2: A W10x30 has a length of 4.80 m. Fy= 248 MPa. The properties are given below. Properties of W shape A - 5,700 mm^2 d-267 mm bf - 148 mm tf - 13 mm kdes - 7.62 mm tw - 14.5 mm rx-111 mm ry-34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are pinned? 311 KN 281 KN O 340 KN O 392 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need clear ans and solve very very fast in 20 min and thank you DYBALA -8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame th (c) Frame ifth (d) Composite Figure (1) (b) Truss क (e) Beam
An A913 Gr. 60 W14x109 is used as a 15-m high column. The column is fixed at both ends and is laterally supported (hinged) at every one-third of its height about the weak axis. 1. Calculate the governing slenderness ratio of the column.2. Calculate the Euler Buckling stress, Fe in MPa.3. Determine the ultimate design strength, in kN
A mountain bike manufacturer is considering a new product line that will include handlebarextenders applied to the ends of the handlebars, as shown below. To validate this design change,you have been tasked with analysing the structure. You have produced an idealised structure, shownbelow, where you consider half the length of the handlebars with a fixed boundary condition (A)applied to the plane of symmetry. You have estimated that the maximum load that a rider can applyto one handlebar extension is 75 Newtons that acts 100 mm from the centreline of the handlebars.The handlebars have a circular cross-section with an outer diameter of 32 mm and a wall thicknessof 3.25 mm. P1 is the critical point. If the maximum permissible tensile stress is 150 MPa and themaximum permissible in-plane shear stress is 55 MPa, what is the largest load, P, that can beapplied by the rider? Justify your answer.
A high performance racing plane is to have an aileron control rod made out of unidirectional carbon fibre tubing with the following material properties: elastic modulus E = 90 GPa and compressive failure stress OF,comp= 600 MPa. In order to avoid parts of the internal wing structure the control rod is required to have a bend at the tip as shown in the figure. The rod is L = 400 mm long with an inner diameter of 8 mm and an outer diameter of 10 mm. The length of the bent portion of the rod is = 40 mm . The servo applies a maximum compressive or tensile force of F= 200 N on one end of the control rod as shown in the diagram. The end at which the loading is applied can be considered to be free and the other end of the control rod can be considered to be fixed. Consider the case where the servo applies a compressive force on the tip of the control rod: (i) (ii) X Find the maximum compressive stress in the rod and the maximum transverse deflection of the rod at B. Find the maximum…
P4: Calculate the design moment strength of the T-section shown in the following figure (fe' = 28 MPa and Fy = 420 MPa). 111 100 cm 3.5mm 3=22 350 E 3.25 m 250 3=22 3.25 250 m
I need the answer as soon as possible
Pls help me
E pe Vi5 For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s. Damping is 10% of critical. Cross-sectional dimension of each column is 250 mm x 300 mm and elastic modulus is 22.8 GPa. Determine (a) () (c) the natural frequency (rad/s) the amplitude the expression for the displacement 500 kN 3 m 5m 5 m
FOS given , so consider it. Thanks
Please read instructions carefully.
Maximum shear force value A 2 ft B 100 lb/ft 2 ft 300 lb AC 200 lb 2 ft
Steel column pinned at both ends has a modulus of elasticity E = 2 x 105 N/mm², moment of inertia I = 90000 mm4, L = 1.75 m, value of Euler's critical load will be