i need clear ans and solve very very fast in 20 min and thank you DYBALA 8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame (c) Frame 杰 (d) Composite Figure (1) (b) Truss क (e) Beam

i need clear ans and solve very very fast in 20 min and thank you DYBALA 8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame (c) Frame 杰 (d) Composite Figure (1) (b) Truss क (e) Beam

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.2 in.2 and an elastic modulus of 1820 ksi. Bar (2) has a cross-sectional area of 1.185 in.2 and an elastic modulus of 3590 ksi. Assume L1=21 in., L2=48 in., Q=7.6 kips, P=2.6 kips, and R=12.8 kips. Determine the horizontal deflection of end C relative to end A.
Mechanics of Materials
For the simple truss shown in the picture the students are required to determine a combination of values for the cross-sectional area of the truss members and the angle 0 that will allow the structure to be both safe for example, the axial stresses developing within the truss elements are less than the yield stress fy = 500MPA and cheep, provide that the cost of the material is cost = 1.1£/kgr. Assume that the density of the material is 8100 kgr/m³. It is noted that the structural analysis has been already carried out for and the analytical relations expressing the internal forces have been provided in the picture. P=2000 KN cost Ray -Reye %½. taco Kw PEA Tel PAB EA Ray E,A lon Pazo Ray/ Ray Sime Pascose + Pac -> Parea -Pao coso Paca Ray coe Ray cose Sino
Given the assumptions made in thin plate bending theory are already known,take a rectangular four-node thin plate bending element as an example and discuss compatibility of the element. (A diagram would be very useful) thanks
Question 2 In the below structure, the truss members stiffness matrix has been used for truss members and the beam stiffness matrix has been used for the rest. a) How many unknown displacements are in the displacement vector? b) How many displacements are in the displacement vector altogether? * J A
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a= 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 31 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft O 3.74 kips 4.77 kips (1) B 3 ft 8 ft 1.5 ft 2 D
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 38 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 5.16 kips 4.86 kips 2.48 kips 3.88 kips O 4.09 kips (1) B 3 ft P 8 ft 1.5 ft
A uniform beam of weight Wis supported by the two rods, the lower ends of which are at the same level just before the beam is supported, as shown in figure. The ratio of the areas Aluminium (E = 70 GPa) 2 m 1.5 m W 3 m 3m Aaluminium Asteel Steel (E = 200 GPa) 0.5 m of the rods so that the beam will be horizontal after it is attached to the rods is
The assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).
A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius 10 m by applying a pure moment M. If Young's modulus tilde E = 200GPa then the magnitude of M is? (a) 72 Nm (c) 216 Nm (b) 144 Nm (d) 288 Nm
Solve step by step in digital format please