right sides of the segment are 75 kN-m and 79 KN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b₁ = 135 mm, b₂ = 50 mm, b3 = 205 mm, d₁ = 65 mm, d₂ = 180 mm, d3= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam. b₂ d₂ МА Ma Answer: Tmax Ax B X MPa by

right sides of the segment are 75 kN-m and 79 KN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b₁ = 135 mm, b₂ = 50 mm, b3 = 205 mm, d₁ = 65 mm, d₂ = 180 mm, d3= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam. b₂ d₂ МА Ma Answer: Tmax Ax B X MPa by

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the Global stiffness matrix of the continuous beam shown. Assume EI is 150kN -m² is constant for each element.*For uniform load Q= 48 kN/m*For concentrated load P= 48 kN
An offset h must be introduced into a solid circular rod of diameter d. Knowing that the maximum stress after the offset is introduced must not exceed 6 times the stress in the rod when it is straight, determine the largest offset that can be used. P' 4 P' P The largest offset that can be used is h = d.
Calculate the shear stress on a-a plane.
For the cantilever bearn shown, determine the normal and shear stresses acting at point K. The cross-sectional dimensions of the beam cross section and the location of point K are also shown. Use the following values: a = 2.15 m, b = 0.80 m, Py 10 kN, P₂ = 8 kN, b = 165 mm, k = 59 mm, t = 12 mm, h = 42 mm, t = 6 mm, and d = 260 mm. by "
Plz help
Solve it ASAP
9 MPa 7 MPa 5 MP 1. Draw the appropriate Mohr's circle. 2. Get from the circle oi and o2, Umax and its corresponding normal stress (Oevg). Show these points on the circle. 3. Show on the circle the angles 20p and 20s that correspond to the orientation of principal planes and the planes of maximum shearing. 4. Solve point (1c) above graphically using the circle ik. show that your graphical solution is giving the same results as obtained by the analytical equations in point (1c) above.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.4 mm and upward by v = 5.8 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 730 mm, α = 25°, and β = 65°.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
Steel structure design
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
please draw the diagram. thanks