A short post carries a downward load P = 133 kN as shown in the figure. Due to its eccentricity from the centroid of the cross-section, it creates combined axial and bending stresses. If the dimensions of the post are: a = 333 mm, b = 205 mm, and c = 631 mm, determine the combined normal stress at point O. (in MPa) Indicate negative sign if necessary considering + for tension and - for compression. 1 P

A short post carries a downward load P = 133 kN as shown in the figure. Due to its eccentricity from the centroid of the cross-section, it creates combined axial and bending stresses. If the dimensions of the post are: a = 333 mm, b = 205 mm, and c = 631 mm, determine the combined normal stress at point O. (in MPa) Indicate negative sign if necessary considering + for tension and - for compression. 1 P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

respectively. E = 2.1 x 10 N/mm? and Poisson's ratio u = 0.3. Determine the magnitude of the In a stressed member 30 principal stress. 445 10" 1..eion: 30 32 10
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
What is the average normal stress at segment AB. Crosssectional Area for AB= 50 mm^2 and BC=100 mm^2. P=10 kN. Length of segment AB= 150 mm and BC =150 mm). B AAB Авс LAB LBc O A. 0.10 MPa (Compression) O B. 100 MPa (Compression) O C. 0.2 MPa (Tension) O D. 200 MPa (Tension)
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 4300 mm² and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A₂ = 2550 mm² and an allowable normal stress of 125 MPa. Assume x₁-23m.x₂-3.9 m.y1 = 1.4 m, and y₂ = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ Answer: Pmax= i| B P ! KN
Find the normal stress, shear stress, and bending deformation of the beam. For the cross-sectional area: by = 0.75 meter, d = 1 meter, tw = 0.10 meter, and tf = 0.15 m.
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
P1.4 Three solid bars, each with square cross sections, make up the axial assembly shown in Figure P1.4/5. Two loads of P = 30 kN are applied to the assembly at flange B, two loads of Q = 18 kN are applied at C, and one load of R = 42 kN is applied at end D. The bar dimensions are b₁ = 60 mm, b₂ = 20 mm, and b3 = 40 mm. Determine the normal stress in each bar. (1) b₁ B P (2) FIGURE P1.4/5 (3) Q D R
A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. 3 Answer: Tmax = psi 1/3