A 24-mm-diameter solid shaft is subjected to an axial force of P = 4700 N, a horizontal shear force of V = 1600 N, and a concentrated torque of T=130 N-m, acting in the directions shown. Assume L- 115 mm. Determine the normal and shear stresses at: (a) point H. (b) point K. For each point, show these stresses on a stress element. y H. K Answers: MPa, 6 = MPa = Point H:o, = MPa. MPa 6, = MPa. = Point K: o, =

A 24-mm-diameter solid shaft is subjected to an axial force of P = 4700 N, a horizontal shear force of V = 1600 N, and a concentrated torque of T=130 N-m, acting in the directions shown. Assume L- 115 mm. Determine the normal and shear stresses at: (a) point H. (b) point K. For each point, show these stresses on a stress element. y H. K Answers: MPa, 6 = MPa = Point H:o, = MPa. MPa 6, = MPa. = Point K: o, =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

#11 Normal stress in rods 1 and 2
The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 7 kN and Q=5 kN. Determine the normal stress in the rod at x = 0.4 m. Assume a = 0.5 m and b=0.9 m. a Answer: σ= i B MPa O
Q.43 Consider a steel (E = 200 GPa) column hinged on one side and fixed on the other side. Its height is 1.5m and the cross-section is 20 mm x 25 mm. The Euler's critical stress(in N/mm²) is...
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the max stress element in each case. Solve the question using Mohr Circle. OX = 41 gy = 41 x 2 EXy = 41 /2 %3D
7
Within few minutes
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 40 ksi, Sy = 17 ksi, and Sxy = 10 ksi. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (c) Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16). (d) Determine the absolute maximum shear stress at the point. Sxy Sx Answer: (a) Draw Mohr's Circle for this state of stress. (b) Op1 = ksi Op2 = i ksi Tmax in-plane i ksi
The solid circular section EF rod in the figure is fixed to the wall at point F. Forces P1 = 1 kN, P2 = 2 kN were applied from point D of the DE rod, which is rigidly connected to the rod. Calculate the stress states occurring at points A and B and show them on the small volume elements removed from these points. The diameter of the EF rod will be taken as d = 50 mm. Do not give answer in image and hand writing
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
Stress in shaft due to Bending Load and Torsion. A shaft has a diameter of 4 cm. The cutting section shows in the figure is subjected to a bending moment of 2 kN-m and a torque of 2.5 kN-m. Determine: 1. The critical point of the section 2. The stress state of the critical point 3. The principal stresses and its orientation Using Morh’r and Draw Stress element transformation
len 9