Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P = 34 kN are applied to theassembly at flange B, two loads of Q = 24 kN are applied at C, and one load of R = 60 kN is applied at end D. Bar (1) has a width of b₁ =98 mm. Calculate the width b₂ required for bar (2) if the normal stress magnitude in bar (2) must equal the normal stress magnitude inbar (1).Pb₂R(1)A↑ DAnswer:b₂ = iBP(2)mm

Answered: Image /qna-images/answer/825926c7-825a-4ca2-9cf4-6f200f4435b7.jpg

Answered: the width b₂ required for bar (2) if t

Engineering

Civil Engineering

the width b₂ required for bar (2) if t

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is made from three boards nailed together as shown. If the moment acting on the cross section is M = 600 N.m, %3D (a) determine the maximum bending stress in the beam. Mc (b) Sketch the stress distribution acting over the cross section. Of = - I 25 mm Mc I 150 mm 20 mm 200 mm M = 600 N•m 20 mm |
Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P = 22 kN are applied to the assembly at flange B, two loads of Q = 12 kN are applied at C, and one load of R = 30 kN is applied at end D. Bar (1) has a width of b₁ = 101 mm. Calculate the width b2 required for bar (2) if the normal stress magnitude in bar (2) must equal the normal stress magnitude in bar (1). P (1) R C A Answer: b2 = i B P (2) mm D
The 2 D stress at a point is given by the matrix 6 50 15 MPa. The maximum 15 10 Txy 6 yy = yx shear stress in (MPa) units is : (a) 45 (c) 25 (b) 55 (d) 30
A rigid block of mass M is supported by three symmetrically spaced rods as shown in figure. Each copper rod has an area of 900 mm^2; E = 120 GPa; and the allowable stress is 70 MPa. The steel rod has an area of 1200 mm^2; E = 200 GPa; and the allowable stress is 140 MPa. (a)Compute the stress of the copper rod. (b)Compute the stress of steel rod. (c)Compute the largest weight which can be supported.
Question 1. The plane NN' makes an angle 0=30° with respect to the cross section of theprismatic bar shown in Figure. The dimensions of the rectangular cross section of the bar are 3cmx6cm. Under the action of an axial tensile load P, the normal stress of NN' plane is ơn =60 MPa. a.Determine the value of axial load P b.Determine the shear stress t on the NN' plane c. Determine the maximum shear stress in the bar. P N N'
The rod has a diameter of 40 mm. Determine the state of stress at point A and draw the resulting 3-D stress element. 1500 N 600 N 300 mm 100 N-m 800 N 100 mm B
The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress at section a-a at the specific points. What is the normal stress at point B in MPa if p=85kN? 200 200 mm -300 mm-
The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress at section a-a at the specific points. If P=65kN, what is the normal force at point A in MPa? 200 200 mm -300 mm- MOMISTAL 20 mm
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A, = 3050 mm? and an allowable normal stress of 65 MPa. Bar (2) has a cross-sectional area of A2 = 3000 mm? and an allowable normal stress of 65 MPa. Assume x1 = 1.8 m. x2 = 2.7 m. y1 = 1.0 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
Solve it fast.
8. An aluminum tube, 1.2 m long, has the semicircular cross section shown in the figure. If stress concentrations at the corners are neglected, determine (1) the torque that causes a maximum shear stress of 40MPA.and (2) the correspond- ing angle of twist of the tube. Use G = 28 GPa for aluminum. 2 mm - 25 mm 3 mm 2