Required information A hollow member having the cross section shown is formed from sheet metal of 0.2-mm thickness. Knowing that the shearing stress must not exceed 2.6 MPa, and that a=52-mm, b=14-mm and c-19-mm, determine the allowable torque that can be applied to the member. P

Required information A hollow member having the cross section shown is formed from sheet metal of 0.2-mm thickness. Knowing that the shearing stress must not exceed 2.6 MPa, and that a=52-mm, b=14-mm and c-19-mm, determine the allowable torque that can be applied to the member. P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Read the question thrice then after solve it. I have other websites answers please don't copy that solutios. Thank you
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
Assume that the clamp shown has been tightened on wooden planks being glued together until P = 420 N. Determine the stress in A and D Find the location of the neutral axis
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
6
i need the answer quickly
please answer all the questions with complete solutions and draw a proper free body diagram. Thank you
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
A structural member is fabricated with the cross section show below and is eccentrically loaded with F. - 26--| F 2t F b. Use G = 77.2 GPa. If I = 4 m, t= 3 mm, b = 80 mm, and F = 121 kN, Determine the maximum shear stress due to torsion. Select the correct response: 168.056 MPa 215.278 MPa 155.556 MPa of 133.333 MPa 22
: Consider the truss shown in the figure below, and answer the following questions. Figure is not to scale. P P R K 5 m B C D E F - 2 m --2 m - 2 m - 2 m- 2 m-- 2 m - a) If P and R are non-zero forces and Q = 0 kN, indicate all the zero-force members in the truss. O LB O LC O KC O KD O JD O ID O IE О НЕ О НЕ O None b) Following from the situation described in Part (a), how many additional zero-force members will there be in the truss in the following situation? If the force R acting at node H is removed.