Required information 10-m-long steel rails of a railroad track (Es = 200 GPa and as = 11.7 × 10-0PC) were laid at a temperature of 9°C. Determine the normal stress in the rails when the temperature reaches 48°C, assuming that the rails are welded to form a continuous track. The normal stress in the rails is MPа.

Required information 10-m-long steel rails of a railroad track (Es = 200 GPa and as = 11.7 × 10-0PC) were laid at a temperature of 9°C. Determine the normal stress in the rails when the temperature reaches 48°C, assuming that the rails are welded to form a continuous track. The normal stress in the rails is MPа.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1. P- 10000 Ib 4 in
* Your answer is incorrect. The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial distributed loading along its length of w= 9 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.5 m. Assume a = 0.7 m and b = 1.3 m. W B >x 45012 MPa a Answer: 0 = b
As shown in the figure, when the temperature was 24 ° C, a 0.5 mm gap was left. Determine the approximate value (° C) of the required temperature so that the normal stress in the aluminum bar is 75 MPa.
This is a subject of strength of materialsShow complete solution and clear hand writing no shortcut pls shoe free body diagram and pressure diagram thank you
For a steel rod with a circular cross section with a diameter of D = 20 mm, the following is required: 1. Draw a diagram of the longitudinal force 2. Draw a diagram of normal stresses 3. Determine the total elongation of the rod if Е = 2∙10^5 MPa When calculating, take: а = 2 m, b =1.2 m, F=10 кN - The point of application of force! The work must be done on one sheet of A4 paper, which must show: - Using the method of sections to determine the longitudinal forces in the rod. - Draw a diagram of longitudinal forces N - Determination of normal stresses based on the constructed plot of longitudinal forces. - Draw diagram a normal stresses - Determination of the full extension of the rod
OP= 314 N Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm, determine the applied force F. Select one: O F= 2285 N O F=7140 N. O F=3427 N OF=5712N OF= 2856 N O F=8568 N Finick a al TO 4
O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall pressure vessels(1-sphere and 2-cylinder), and one on thick wall cylinder, given below. A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa, determine the radial and tangential stress. Determine the maximum shear stress in the cylinder. Assume it has closed ends.
ru 8 бу enüz vaplanmadı Ot D0 uzerinden retlenmiş Txy Soruyu retle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the minimum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
The temperature of an aluminum bar and a steel bar was raised from 40°C to 160°C. If there was a gap 0.4 mm between the two bars at 40°C as show in figure below, determine the normal stress in the aluminum bar and the change in length of the aluminum bar. 0.5 mm 300 mm 250 mm B Aluminum Stainless steel A = 2000 mm² E = 75 GPa A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C %3D %3D a = 23 X 10-6/°C
i need the answer quickly
Please give neat and proper step by step solution. A tie rod of uniform section is required to resist a force of 450 kN at an eccentricity of 25 mm from the axis of the rod. Determine the size of the tie rod if the permissible stress is limited to 125 N/mm².
Please full solution with the drawing. Big and clear handwriting