Release of drug from a 20mm gel cube (B) was tested by placing it in a large dissolution apparatus containing a buffered solution into which the drug (A) was extracted. 4 of the sides are sealed, while 2 opposite sides are not. If Xp = 0.4, and DAB = 1.8 x 106 cm/s, what is t (hr)?

Release of drug from a 20mm gel cube (B) was tested by placing it in a large dissolution apparatus containing a buffered solution into which the drug (A) was extracted. 4 of the sides are sealed, while 2 opposite sides are not. If Xp = 0.4, and DAB = 1.8 x 106 cm/s, what is t (hr)?

Biochemistry

9th Edition

ISBN:9781319114671

Author:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Publisher:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Chapter1: Biochemistry: An Evolving Science

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

number 57.) what's the answer
Dosage Calculations Calculate the following dosages. What volume of PCN G is in one dose? Ordered: PCN G 1.25 mil units Available: Multidose vial labeled 500,000 units/mL after reconstitution
An IV infusion is to contain 40 mEq of potassium ion and 10 mEq of sodium ion in 500 mL of D5W.Using a 20% w/v potassium chloride injection (MW 74.5, valence of 1) and 0.45% sodium chlorideinjection (MW 58.5, valence of 1), how many milliliters of each should be added to the 500mL bag ofD5W to supply the required ions?
A patient is to receive Tazidine by intramuscular injection. A 10.0-mL vial contains 1 gram of dry powder that was reconstituted with 3 mL of sterile water. The reconstituted solution contains 340 milligrams Tazidine in 1.00 mL of volume. How much solution should be injected if a patient needs to receive a 0.30 gram dose? Enter the numerical part of the answer in the first box (using correct significant figures) and the correct unit in the second box.
It takes 175ml of 0.75 M H2SO4 to completely neutralize 285 ml of NaOH. What is the concentration of the NaOH solution?
25. ATROVENT Nasal Spray contains 0.03% of ipratropium bromide in a 30-mL me- tered dose container. If the container is calibrated to deliver 345 sprays, calculate the volume of each spray, in microliters, and the medication content of each spray, in micrograms. 25. 86.96 µL /spray and 26.09 µg ipra- tropium
An order was received for 750 mL of 7.5% dextrose solution using 5% D5W and 20% D20W. How many parts of each dextrose solution is needed?(round answers to the nearest tenth)
A pharmacist is preparing a compounded oral suspension preparation using commercially available tablets as the source of the active pharmaceutical ingredient (API). The recipe is as follows: "API" 0.8 mg/mL Structured suspension vehicle qs ad 240 mL Sig: 1 tsp PO BID PRN The tablets are available at a strength of 20 mg. Assume that when the the minimum number of tablets is used to prepare this compounded suspension, the crushed tablets take up 12.2 mL of volume.What volume of suspension structured vehicle will be needed to prepare this compounded oral solution?Round the answer to one decimal place.
Consider the following from the Ampicillin for Injection, USP package insert: For Intramuscular Use: Label Claim 250mg 500mg 1g 2g Amount of Diluent (mL) Approx. Volume (ml) 0.9 1.7 3.4 6.8 1 2 4 8 a) What is the amount of diluent needed to reconstitute a 1 g vial? b) What is the powder volume for a 1 g vial of ampicillin? Approx. Concentration (mg/mL) 250 250 250 250 Later in the package insert you see: For Direct Intravenous Use: Add 5 mL Sterile Water for Injection or Bacteriostatic Water for Injection to the 250 and 500 mg vials and administer slowly over a 3 to 5-minute period. Ampicillin for Injection, 1 g or 2 g, may also be given by direct intravenous administration. Dissolve in 7.4 or 14.8 mL Sterile Water for Injection or Bacteriostatic Water for Injection, respectively, and administer slowly over at least 10 to 15 minutes. c) What is the amount of diluent needed to reconstitute a 1 g vial of ampicillin for direct IV injection d) What is the total amount of volume that will…
Plot a line weaver-burk graph for Km=6.30mM and Vmax=360uM/min when an experiment has 5 tubes with concentrations of substrates of 1.0mM, 10mM, 50mM, and 100mM.
points) You have to make 50mL of 0.05M HCI from a 10M HCI stock solution, but the onlymeasuring devices available are 100mL graduated cylinders and 10mL serological pipes. Howcould you accurately make the dilute HCI solution (clearly explain)?
Four lab groups completed the experiment listed in the lab diluting lul of FCF dye into 1ml of water. The A625 values are listed below. For brilliant blue FCF, ɛ =97000 M-1cm–1 MW = 792.8 g/mol %3D Group # A625 % solution (in original stock sample) Percent ror (True value of Stock=0.2%) 1 0.244 0.199 0.5 0.209 0.170 15 3 0.306 0.250 25 4 0.187 0.153 0.235 a. Which group was more accurate? b. What are possible reasons group 3 had a much higher Absorbance than the others? c. What are possible reasons group 4 had a much lower Absorbance than the others?