Refer to the flow shown in the figure. The velocity before the contraction is 1.51m/s. Given:h=0.20mD1=0.103mD2=0.057mDetermine the height of the fluid in the manometer, H, in meters Refer to the the flow shown in the figure. The velocity before the contraction is 1.51 m/s.Given:h = 0.20 mD1 = 0.103 mD2 = 0.057 mD₁HhFree jet flowDetermine the height of fluid in the manometer, H, in meters.Express your answer in 2 decimal places..

Given:- Velocity before the contraction = 1.51 m/sh=0.20 mD1=0.103 mD2=0.057 m To find:- Height of…

Answered: Refer to the flow shown in the figure.…

Refer to the flow shown in the figure. The velocity before the contraction is 1.51m/s. Given: h=0.20m D1=0.103m D2=0.057m Determine the height of the fluid in the manometer, H, in meters

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure difference between two points as measured with a manometer is given as ?2 − ?1 = ??ℎ The following figure shows a single U-tube manometer for measuring pressure difference between points “A” and “B”. By determining the pressure at point “a” through the left leg and then through the right leg, show that the difference in pressure between point “A” ?? and “B” ?? is approximately given by ?? − ?? ≅ ?(ℎ2 − ℎ1)(??2?)
The velocity profile of a liquid flowing through the pipe is approximated by the truncated conical distribution as shown in (Figure 1). Suppose that V = 4 ft/s. Hint: The volume of a cone is V= r²h. 0.3 ft 0.6 ft V 0.3 ft Determine the average velocity of the flow. Express your answer to three significant figures and include the appropriate units.
Determine the gauge pressure at the center of pipe B in kilopascals. Mercury (S = 13.6) is the fluid in the manometer while oil (S = 0.93) is the fluid flowing in the pipe. Oil Mercury +B 0.2 m 0.02 m
A box with one inlet and two outlets is shown in the figure below. The fluid is oil with a specific gravity (SG) of 0.79. The weight of the oil in the box is 2500 N. Only the outlets are open to the atmosphere. Calculate the force components Fx and Fy required to hold the box stationary. Neglect the weight of the box. Q3 = 3.0 m3/s V3 = 1.5 m/s V2 = 2.0 m/s 03 = 60° 02 45° Q1 Vị = 2.0 m/s P1 = 4000 Pa = 5 m/s F, F, Fx i 14330.9 N Fy i 5918.47 N II
The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L₁ = 3 ft, L₂ = 0.5 ft, and L3= 1.25 ft. The densities of the oil and mercury are 55 and 845, respectively, each in lb/ft³. Let g = 32.2 ft/s². Pgage = i Pressure gage lbf/in.2 Air Determine the reading of the pressure gage, in lbf/in.2 (gage). Oil (p=55 lb/ft³) Pam Mercury (p=845 lb/ft³) g=32.2 ft/s²
USE DOUBLE INTEGRATION METHOD TO ANSWER THE PROBLEM. The given figure is a hollow steel tube to be used as a beam. Determine the self-weight (dead load) per meter. 50 mm D. 250 mm 750 mm 35 mm
(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=1.7 ft/s h = H= 6.4 in. Air ↓ SG= 1.10 ft ft TH 3.8 in.
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
Fluid Mechanics Given: A square tank (open to the Atm) holds 3 feet of oil on top of 6 feet of water. An outlet pipe that is 2 inches in diameter provides an outlet for the water. The outlet is located 2 feet above the bottom of the tank. Find: Neglecting friction energy loss, determine the discharge of water out of the tank. The specific gravity of the oil is 0.86.
The Newtonian fluid shown in is confined between the plate and a fixed surface as shown in (Figure 1). Its velocity profile is defined by u = (8y-0.3y2) mm/s, where y is in mm. The plate has a surface area of 29(10³) mm² in contact with the fluid. Take μ = 0.482 N. s/m². Suppose that h = 6 mm. Figure h < 1 of 1 Part A Determine the force P that must be applied to the plate to cause this motion. Express your answer to three significant figures and include the appropriate units. xa P= 67.1 μA Xb a b X.10n < Return to Assignment mN Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ? Provide Feedback
The top part of a water tank is divided into two compartments, as shown in given figure. Now a fluid with an unknown density is poured into one side, and the water level rises a certain amount on the other side to compensate for this effect. Based on the final fluid heights shown on the figure (h1 = 76.8, h2 = 45.2, and h3 = 96.5 cm). Determine the density of the fluid added. Assume the liquid does not mix with water and the density of water is 998.2 kg/m. !! %3D Unknown liquid h3 WATER h2 (use one number after the decimal xxx.x)
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).