**Manometer Problem with Multiple Liquids:**This diagram illustrates a manometer containing three different liquids: water, mercury (Hg), and oil. The specific gravities (SG) of the liquids are provided, and the task is to calculate the gauge pressure for the oil.**Key Information:**- **Water Column:** - Height: 10 cm - Pressure: 20 kPa- **Mercury (Hg) Column:** - Height: 20 cm - Specific Gravity (SG): 13.6- **Oil Column:** - Height: 10 cm - Specific Gravity (SG): 0.9 - Unknown gauge pressure (??)The figure shows the arrangement of these columns, with water at the bottom, mercury in the middle section, and oil at the top. The goal is to determine the gauge pressure exerted by the oil.

Given, to determine, Gauge pressure for oil.

Answered: Manometer with three liquids as shown.…

Manometer with three liquids as shown. SGs are given. Calculate gauge pressure for oil. 20 KPa Water 10 cm 10 cm 20 cm TI Oil SG=0.9 Hg SG= 13.6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

show complete solution and diagram
Question 3:- A tank with 100.58 kPa pressure is connected with manometer to measure the pressure. The specific gravity of fluid was 0.85 and the atmospheric pressure is 96 kPa find the manometer column height "h". Pam = 96 kPa P=100.58 kPa h=? SG = 0.85
please answer this as fast as you can. It would help a lot
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3. pls answer asap thank you
Please solve it fast.
The shaded area whose dimensions are given in the figure;Calculate the radius of inertia Ix. a: 10cm
The Newtonian fluid shown in is confined between the plate and a fixed surface as shown in (Figure 1). Its velocity profile is defined by u = (8y-0.3y2) mm/s, where y is in mm. The plate has a surface area of 29(10³) mm² in contact with the fluid. Take μ = 0.482 N. s/m². Suppose that h = 6 mm. Figure h < 1 of 1 Part A Determine the force P that must be applied to the plate to cause this motion. Express your answer to three significant figures and include the appropriate units. xa P= 67.1 μA Xb a b X.10n < Return to Assignment mN Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ? Provide Feedback
A tape of 20m length is used to measure a distance 1980 m at a temperature 35 °C oumale borte under 20 N tension force, find the correct measured distance if: down: STEFTICAGES Standard temperature20 °C Coefficient of thermal expansion 11.6*10 Mass of tape is 0.04 kg/m Standard tension 60N Cross section area of tape 2mm² Modulus of elasticity of tape 2000000 kg/cm²
3. What is the equivalent height in meters of glycerin (sg = 1.26) for an absolute pressure of 5 atm when barometer reads 800 mm Hg. Also find the equivalent height of oil (sg = 0.8) in inches.
Read the question carefully and give me right solutions with clear calculations
Which of the following unit is NOT the Pressure unit? o Pascal o psi o kelvin o standard atmosphere • A vacuum gage connected to a chamber reads 7 psi at a location where the atmospheric pressure is 14.5 psi. What is the absolute pressure in the chamber? o 7.5 psi o 21.5 psi o -7.5 psi o 8.7 psi Pressure is a scalar quantity, the pressure at a point in a fluid is the same in all directions. o True o False
A piston having a cross-sectional area of 0.23 m² is located in a cylinder containing water as shown in the figure below. An open U-tube manometer is connected to the cylinder as shown. For h₁ = 63 mm and h = 132 mm what is the value of the applied force, P, acting on the piston? The weight of the piston is negligible. P= N Piston TU Water Mercury P