Recommend the low cost flow meter used in industries for measuring flow that provides negligible loss of head in the pipeline. Discuss its construction and working. A venturi tube of throat diameter 10 cm is placed in a pipe of diameter 20 cm. The volumetric flow rate through the venturi tube is 0.02 m3/ sec. [Given: viscosity of water = 10–3 Pas]. Determine the Reynolds number and the upstream to throat differential pressure developed.

Q: A Venturi meter as seen in figure below consists of a tapered constriction in a tube with pressure…

A: Solution: As per continuity theorem, flow rate between point 1 and 2 assuming incompressible flow,…

Q: Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is…

A:

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A: Given data: ◆ The diameter and length of the cast iron pipe: D = 8 cm = 0.08 m , L = 388 m ◆ The…

Q: A non-Newtonian fluid flows from a storage tank to a reactor at an average velocity of 3 m/s through…

A: The average velocity V=3 m/s The length of horizontal pipe h=5 m The pipe flow consistency index…

Q: What is the volume flow rate for water (viscosity= .0010 Pa×s) through a length of pipe L= 0.60m and…

A:

Q: An oil with a dynamic viscosity of 0.8 Pa.s and specific gravity of 0.9 is flowing through a…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: oil (0.88) ► oil (0.88) Hg (SG=13. 320mm-

A:

Q: A pipeline carrying 0.257 m/s water is reduced suddenly from 400 mm to 250 mm diameter (Take Cc…

A: Note: As per Bartleby guidelines only one question has to be solved. So upload other questions…

Q: 5. Water flows in a 30 cm diameter cast iron pipe of relative roughness 0.0008. If the water flow…

A:

Q: Calculate the flow through a three-new steel pipes connected in series having diameters of 6 in., 8…

A: Given data: The diameter of pipe 1, d1 = 6 in. The diameter of pipe 2, d2 = 8 in. The diameter of…

Q: A water is to transport in a 500 mm diameter pipe and connects two reservoirs. The pipe is 3000 m…

A:

Q: Water flows in a pipe at 0.015 m³/s. The pipe is 50 mm bore diameter. The pressure drop is 13 420 Pa…

A:

Q: QI A 0.5 inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is…

A: Given DataQ=19L/minD=0.5 inL=18m

Q: A calibration test of a 15 mm circular sharp-edged orifice in the end of a 50 mm pipe showed a…

A: Given data: The diameter of the orifice is, do=15 mm. The diameter of the pipe is, dp=50 mm. The…

Q: A pipe is often used to assess the flow rate of water in the center of a pipe with an internal…

A:

Q: Problem 1: For the system shown in the diagram below, let 4z = 80 m and L = 185 m of cast iron pipe…

A: To determine:Pipe diameter(D)

Q: A Venturi tube is to be used to measure a flow rate of water in a 120mm pipe. The maximum flow rate…

A:

Q: Water @ 4C flows through a 100-mm ID smooth pipe. The Reynolds # of the flow is 150000. Determine…

A: To Find : The maximum velocity. Given : The diameter is d=100 mm. The Reynolds number flow is…

Q: Oil flows in a pipe 80 mm bore diameter with a mean velocity of 0.4 m/s. The density is 890 kg/m3…

A:

Q: Give

A: As per bartleby guide lines only solve one question, if you want to remaining questions send each…

Q: 4. Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large…

A: Specific gravity of Brine, SG=1.1Viscosity of brine, μ=1.1 cP=1.11488.1639lb/ft.sec=7.3916*10-4…

Q: Water enters a pipe of diameter 22 mm with a venturi meter with a throat diameter of 12 mm. At the…

A:

Q: 6. SAE 10 oil is being released from a main reservoir to a smaller reservoir. The pipeline consists…

A: ◆ The total head loss in the pipeline is the summation of major head loss and minor head loss. ◆…

Q: Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = %3D 2.5in) from large…

A: Given: Specific gravity of the brine→S=1.1 Hence density of the brine→ρ=1.1×62.4=68.64 lb/ft3…

Q: 5.11kg/s liquid is flows through a reduced pipeline. Inlet velocity: 3.3m/s and Outlet velocity:…

A:

Q: 3. Compute the friction head loss in meters of a fluid at a certain condition (S.G.-1.101) that is…

A:

Q: A smooth pipe carries water at the rate of 300 L/s, kinematic viscosity is 10 m/s , with a head loss…

A: Given, Q = 300 L/s = 0.3 m3/s Kinematic viscosity = v = 10-6 m2/s Head loss = hf = 3 m Length of…

Q: A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter…

A:

Q: Medium oil with kinematic viscosity 6.10x10^-6 m²/s, flows through a straight pipe at a rate of 6.0…

A:

Q: I want the method to calculate the Reynolds number, where did this number 435,000 come from(Marked…

A: To compute the Reynolds number (Re), you can use the formula:Re=νVD​where: D = diameterV = velocityν…

Q: An oil and gas company want to measure the flow rate of the oil in a low head loss application. 1.…

A: A device which is used to measure the flow rate of the oil in low head loss application is venturi…

Q: What is the size (thickness) of u' and 8 for turbulent flow in a 4 in (100 mm) nominal pipe?…

A: Find the density of the fluid at a given temperature,

Q: length = 10cm diameter = 4mm length = 10cm diameter =1mm length = 10cm diameter = 4mm diameter = 1mm…

A: Given: velocity at the inlet→V1=0.5 ms Diameter of the inlet pipe→D1=4mm=0.004m Hence area of the…

Q: A pipe of unknown type, length and diameter includes a threaded union (KL = 0.08), 90° %3D threaded…

A: Given data  minor loss coefficients for threaded union = 0.08  minor loss coefficient for 90o…

Q: (b) An oil with dynamic viscosity of 0.8 Pas and specific gravity of 0.9 is flowing through a…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.