The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Pol = 673 kg/m)

The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Pol = 673 kg/m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please give a detailed Handwritten solution.
C. A pump delivers 25 L/s of water with a head of 35 m and runs at a speed of 2950 rpm for 8 hours per day. The shaft power is 11.5 kW. The electric motor driving the pump has an efficiency of 84% and the cost of electricity is 15 cents per kWh. Evaluate the cost of electricity to run the pump in a day.
In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
A groundwater well with produces 80 m/hr. and has a hydraulic conductivity of 20 m/d. Calculate the following: a. The length of the screen b. The diameter of the delivery pipe. c. The velocity head and the friction losses in the delivery pipe. d. What is the required power of the pump if the abstraction efficiency was 70%? Assume the following: The percentage of the opening in the screen is 17%, the entrance velocity is 1.55 cm/sec, the diameter of the screen is 30 cm, water velocity in the tube is 2.2 m/sec. Assume any missing data.
Give detailed solution,Only Handwritten.
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 112 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.92 and sp. gr of oil = 0.8 %3D (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) =
Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is situated 9 m below the level of the source, calculate (Zs)max and determine if the pump is safe from cavitation. Select one: O a. -7.9 m; NOT SAFE O b. -9.7 m; NOT SAFE O c. -7.9 m; SAFE O d. -9.7 m; SAFE
Cou
A manufacturing company uses a 100 bar hydraulic power system which supplies 10 liter/minute of oilflow. The shaft speed is 1500 RPM and the nominal displacement is 8 cm3/revolution. The theoreticaldrive torque is 11.4 Nm. If the electric motor driving the pump has an efficiency of 95%,a. Name in detail all 27 hydraulic power components as illustrated in the above figure.b. Calculate the volumetric efficiency, the fluid and shaft power, the overall efficiency of the pump.
What is the time is taken by the system to fill a tank of capacity 315 liters and flow rate 25 x 10 3 m³ per hour?