Please answer as soon as possible. Water flows into junction J from reservoirs A andBthrough connecting pipes, the head loss throughthese being, respectively 10.Q% and 4.Q. Thewater level elevations at the reservoirs at A and Bare 25.9 m and 18 m, respectively. The inflow at Jis discharged out at Cinto the atmosphere. Thehead loss through pipe JC is 1.Q% . The gauge,".pressure at Jis 9 m. What is the residual gaugepressure of the outflow at C?A, 25.9 mВ, 18 m10.Q%4.0%2J, 9 m1.0%

Given:Head loss in pipe A=10QA2Head loss in pipe B=4QB2water level at A=25.9 mwater level at B=18…

Answered: Water flows into junction J from…

Water flows into junction J from reservoirs A and Bthrough connecting pipes, the head loss through these being, respectively 10.Q% and 4.Q. The ire ot Aend D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated…

Q: On a nautical chart their are times that their are more than one Compass Rose what is the main…

A: Compass Rose

Q: power it has an efficiency of 37%, but that when it needs to be ramped u down to compensate for the…

Q: 1 COP Nth False True

A: 1.COP=1/thermal efficiency False

Q: A Profilometer is used to measure: How hard a part surface is. How round a part is to…

Q: Q1: True and False 1. In USM, tool tips must have high resistance and fatigue strength. 2. The…

Q: Steps in the procedure of measuring the volume of liquid using a graduated cylinder.

Q: Procedure: 1. Look up the materials that make up a smartphone. Take notes in a table like the one…

A: Minerals are the substance found in the earth's crust useful to mankind. Smartphone is a Pinnacle of…

Q: From the following identify the false statement . In general safety precaution the machine should…

A: Precaution and safety

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: 9- Crude oils with a large volume of issolved gases are less dense, light in eight, and have high…

A: Yes, it is true.

Q: Successive approximation type ADC is used in most of the applications . Select one: True False

A: Successive approximation type ADC is used in most of the applications. This Statement is true.

Q: 6-The (Pitot Tube) it is used to measure the speed of the air and gases in various industrial…

A: This question is based on the concept of pitot tube from fluid mechanics.

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 1 3. 9 TypehereIG 2.

A: Correct option: True.

Q: Mercury has a uniform coefficient of expansion Select one: O True O False

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work done to keep the system in good…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 289 K and…

Q: Q2/ Which part of speech the word "patently" ?belongs to „Adverb .a .Noun .b .Adjective .c .None one…

A: The patent is a verb or noun and it can be an adjective.

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: This problem is based on Bratton cycle and can be solved as :

Q: Particles less than in diameter are generally referred to as the fine mode: a. 0.75 μm; b. 7.5 um;…

A: This question is based on the concept of size of particles.

Q: 6. Nickel and titanium, at a certain alloy composition can be a ] steel alloy J crystalline material…

Q: Which one of the below statements is mostly NOT correct about in creation of detailed design of…

A: The correct option is third. That is in selection of manufacturing process no. of components need to…

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: Some boilers do not require separators, since they: a. Operate above critical temperature. b.…

A: There is no boiler drum in a super critical boiler so separator is not required.

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given - L = 25 ft = 25 × 12 P = 10000 lb ∆L = 0.477 in E = 30 × 106 psi

Q: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

A: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

Q: The risk of damages in the life of a machine component can be eliminated by using individual…

A: This statement is (TRUE)

Q: PMM1 means, the machine does not follow the second law of thermodynamics Select one: True False

A: False

Q: Gas welding process creates a messy work piece. Select one: True False

A: True In gas welding process oxy acetylene gas combustion take place and heat produced is utilised…

Q: From the following identify the false statement. O In electrical safety precaution, necessary steps…

A: From the above options ..

Q: In conductivity method of level measurement when the liquid is short of the required level, the…

A: Conductivity level measurement: In conductivity level measurement, conductivity level sensors detect…

Q: ft. B `4 ft 8 ft 3 ft A Figure 03.12(a)

Q: Which statement is true in the case of the term "Precision". The closeness of output readings when…

A: Precision: It is the measure of consistency or repeatability of measurement of an instrument.…

Q: 1a) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 43 mm and…

Q: Interchangeability system is also called

A: Solution:

Question

Please answer as soon as possible.

Water flows into junction J from reservoirs A and
Bthrough connecting pipes, the head loss through
these being, respectively 10.Q% and 4.Q. The
water level elevations at the reservoirs at A and B
are 25.9 m and 18 m, respectively. The inflow at J
is discharged out at Cinto the atmosphere. The
head loss through pipe JC is 1.Q% . The gauge,".
pressure at Jis 9 m. What is the residual gauge
pressure of the outflow at C?
A, 25.9 m
В, 18 m
10.Q%
4.0%
2
J, 9 m
1.0%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Mark the correct definition
From the following identify the true statement. OIn general safety precaution, the operator should know the procedure to switch OFF the power and lock it in position. O In housekeeping safety precaution, compressed air should not be used to clean the machine. O In electrical safety precaution, all non- metallic parts externally accessible must always be earthed. O In general safety precaution, the inflammable materials need not be kept near to electrical controls
is a type of data presentation device, where its output is recorded on a sheet of paper as a sequence of numbers. digital recorder analog recorder O digital indicator O analog indicator
Choose correct answer: PMM2 means that a machine follows 2nd law of thermodynamics Select one: True False
None
I need answer within 20 minutes please please with my best wishes
In general, in oil and gas industry, the wells are classified into Onshore & Offshore wells. Select one: True False
When several measured values are close to the standard or accepted value, the values are said to be precise accurate neither accurate nor precise both accurate and precise
Moving to another question will save this response. èstion 10 With respect to a fitting operation, which of the following is the correct sequence of events? O A. Marking-Measuring-Filing B. Measuring-Marking-Filing C. Filing-Measuring-Marking O D. Marking- Filing-Measuing Windows buukl eIT:PA T-TV E/IV
follow the steps while answering step by step detailed answer good HANDWRINTING (DONT REJECT LET OTHER ANSWER THE QUESTION IF YOU DONT HAVE IDEA THEN SKIP)
What is global warming? Write any two ways that how global warming is affecting the environments? Short answer
1- You have been asked to decide which one can be used for the dental handpiece water supply; a compressor or pump, which one you recommend, why?