A compressor delivers 2000 cfm of air through a pipe at a receiver pressure of 140 psig. What minimum size schedule 40 pipe should be used if the pressure loss is to be limited to 0.10 psi per foot of pipe length?

Q: 4- In the (Venturi-Meter Experiment) calculation the...volume/time. a-Re. b- Qactual d-Other…

A: Venturimeter is a device which is used for measuring the rate of flow through the pipe. Principle:…

Q: Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water…

A:

Q: Differentiate between major and minor losses in pipes.

A: Pipe is a closed conduct which is used for caring fluids under pressure because pipe carry fluids…

Q: What is the pressure drop in psi of 60°F water flowing through 65 ft of horizontal 1-inch schedule…

A: Consider the solution below

Q: ( Use nomograph AND the formula) Size a pipe that will not exceed 48' of HL in 6000 feet of pipe at…

A: Given data: Head loss, HL = head loss due to friction, Hf= 48 ft Length of the pipe, L = 6000 ft…

Q: You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to…

A: A pitot tube is a device that consists of a tube with a brief right-angled bend that is…

Q: What is the energy loss over a gradual contraction from a DN125 Schedule 40 steel pipe to a DN50…

A: Given data Gradual contraction is from section 1 with DN125 schedule 40 pipe to section 2with DN50…

Q: 4. A special oil is to be used in an absorption tower. The preliminary design of the unit requires…

A: A schematic diagram of the given case is Given data, Datum height at section 1, Z1 = 10 ft Length…

Q: CFM Calculation: (Q6) A compressor specification says that it can deliver 4 CFM when the pressure…

A:

Q: running and delivering air at 12

A: Given: t=12 minPmax=180 PsiPmin=155 PsiQr=25 scfmQc=0

Q: WHAT HP (CENTRIFUGAL FAN) IS NEEDED TO SUPPLY AIR MOVING AT 20 FEET PER MINUTE (FPM) THROUGH A 2X3…

A: Given data: v=20 ft/mA=2×3 ft2hw=3 in Need to determine the power required for the fan.

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: ugh a 1.0 in diameter pipe is 3 GPM with a pressure drop of 5 PSI. What would the pressure drop be…

A: Givend1=1inQ=3GPM∆P1=5psid2=1.5in

Q: A fluid is flowing in a round pipe. The Reynolds number is Re = 3 x 10°. The relative roughness is =…

A:

Q: Assemble and describe the operation of a simple piping system (with only one branch, or at most two…

A: Firstly, we need to assemble the piping system. The main pipe will start from the pump, which is…

Q: Problem 3: A submersible deep-well pump delivers 745 gal/ h of water through a 1-in Schedule 40 pipe…

A: Given Data The flow rate of water is:Q=745 gal/h=0.0276644 ft3/s The head loss in pipe is:hL=10.5…

Q: Submit the correct solution .

A:

Q: large tank is partly filled with water, the air space above being under pressure. A 2" hose…

A: pair = 1035.354 psi

Q: Ex. Closed pipe system the length is 130 m and 50 mm in diameter containing sixteen long elbows and…

A: Write the standard values of pipe fitting losses from pipe fitting losses equivalent length table…

Q: which do you think would give a more accurate reading of the flow rate? thourougly justify.

A: Venturi meter is a device which measures the average velocity at a section and pitot tube measures…

Q: manufacturer lists the flow coefficient for a certain control valve as 3.5 at a flow rate of 40…

A:

Q: 4) In a leakage test on a ring main, it was observed that when receiver tank was fully charged to 8…

A:

Q: The critical cavitation number of a pump is 0.12, the vapor pressure head is 0.2 m, the atmospheric…

A:

Q: 12.18 WEY The performance characteristics of a certain centrifu- gal pump having a 9-in.-diameter…

A:

Q: A type of flow measuring instrument that measures the static and velocity pressure  simultaneously…

A: In fluid mechanics we have many flow measurement instruments for different purposes and we use them…

Q: A 6-nominal schedule 80 cast iron pipe is 3500 m long. It is to convey octane at a flow rate of 0.02…

A:

Q: If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes…

A: Given:

Q: 2). Calculate friction heads when a flow rate of 1.5 m³/min circulate in two different pipelines.…

A: Given: The flow rate of water solution, Q = 1.5 m3/min The diameter of pipes, D2 = D1 = d = 2 in The…

Q: Don't use chatgpt. I need right answer.

A: Given:Inner diameter of the hose (di) = 1 inThe inner radius of hose (ri) = di/2 = 1 in/2 = 0.5…

Q: With the given pipe lengths, sizes and connections and if all pipes have an f=0.020. 1. which of…

A: In real life the use of fluid flow in both circular and noncircular pipelines is widespread. The…

Q: Water flows into junction J from reservoirs A and Bthrough connecting pipes, the head loss through…

A: Given:Head loss in pipe A=10QA2Head loss in pipe B=4QB2water level at A=25.9 mwater level at B=18…

Q: Give solution asap , Handwritten required.

A:

Q: INDUSTRIAL PLANT ENGINEERING Select a proper schedule of pipe for each of the following conditions:…

A: Given Datad=10inP=900psiaT=900F

Q: A 10,000-gallon water tank atop a building delivers fresh drinking water for itsoccupants. A…

A:

Q: Air at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a…

A:

Q: Problem #3 The pressure difference between points 1 and 2 in the series pipe system shown below is…

A: The friction factor for pipes is The loss coefficient for sudden contraction is The pressure…

Q: 8.41 Fuel oil (sg = 0.94) is being delivered to a furnace at a rate of 60 gal/min through a 1/2-in…

A:

Lubricants

Lubricant can be expressed as the substance that is applied among surfaces to control the wear and tear and improve performance. Lubricants play an essential part in the safety of machinery components like gears, shaft, linkage, cam, clutches, and many others. The quantities which affect the amount of lubricant are temperature, surrounding conditions, speed of the components, and many more.