Question : Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as shown in the figure. The force required to hold the plate steady is 75 N. Assuming steady, frictionless, one-dimensional flow, estimate Part (a) the velocities at sections (1) and (2) and Part (b) the mercury manometer reading h.

Q: Consider a viscous fi lm of liquid draining uniformly downthe side of a vertical rod of radius a ,…

A: Assume that the steady incompressible flow in the z-direction, the Navier-Stokes for the given case…

Q: A non-viscous fluid is flowing through the pipe as shown. At which location is the pressure the…

A:

Q: Air enters a duct, of diameter D=25.0 mm through a well-rounded inlet with uniform speed, U₁=0.870…

A:

Q: A fluid with specific weight of 12000 N/m³ and viscosity of 0.002 kg/m.s flows between two parallel…

A: Given, γf=12000 N/m3 μ=0.002 kg/m.s b) H=0.2 cm=0.002 m γm=16000 N/m3 c) L=15 cm=0.15 mU=0.007…

Q: Pump Patm = 100 kPa D=3 cm Gasoline, SG= 0.68 x-

A: Given data:  Discharge, Q = 65 gallons/min Q=65×6.309×10-5 m3/s Diameter of pipe, d = 3 cm = 0.03 m…

Q: In Fig.  water exits from a nozzle into atmosphericthe pressure of 101 kPa. If the exit velocity is…

A: Given data Atmospheric pressure P0 = 101KPa Velocity of water at the exit of pipe V2 = 8 m/sec From…

Q: difference between points (1) and (2)?

A: the pressure difference = 9790X(133100/9790-1)*0.12 =14797.2 Pa =14.79 kPa

Q: jet of alcohol strikes the vertical plates shown in the Figure 2.  A force F=425 N is required to…

A: ForceF=425ND1=5cmD2=2cmP2=101kPaAlcohol SG=0.79 To-Determine:- 1) The mass flow rate of alcohol.2)…

Q: A liquid of density 1150 kg/m3 flows steadily through a pipe of varying diameter and height. At…

A: Given data as per question The density of liquid =1150 kg/m3 v1 = 9.47 m/s d1 =11.7 cm d2 =17.7 cm

Q: Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23…

A: Write the formula for the velocity at the inlet of the venturimeter in terms of the pressure at the…

Q: Determine the magnitude and direction of the anchoring force needed to hold the horizontal elbow and…

A:

Q: P4.87 SAE 30W oil at 20°C flows through the 9-cm-diameter pipe in Fig. P4.87 at an average velocity…

A:

Q: A jet of water of diameter 75 mm moving with velocity of 25 m/s strikes a fixed plate in such a way…

A: Given Data: Velocity, v=25 m/s Diameter of jet, d=75 mm

Q: Consider the large open tank of water. At a height, h = 1 m, above the bottom, it is connected to a…

A:

Q: A volumetric flow rate Q of isopentane of density ρI flows through a pipe of crosssectional area A,…

A:

Q: Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1…

A:

Q: A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameter…

A: According to the continuity equation, the product of fluid velocity and cross-section area of the…

Q: A closed-form expression for the mass flow through a choked nozzle is poA* |Y 2 (y+1)/(y-1) T V R \y…

A:

Q: Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal…

A:

Q: A piezometer and a Pitot tube are tapped into a horizontal water pipe, as shown in Fig. below to…

A: Given:- h1=3cm=0.03m h2=7cm=0.07m h3=12cm=0.12m Point 2= stagnation point  h1+h2=hstatic…

Q: A viscous laminar fluid between two parallel plates is driven by the top plate moving at a constant…

A:

Q: A cylindrical tank 1 m diameter and 3 meter high contains 1m of water, 1.2 m of oil (SG=0.8) and air…

A:

Q: Water flows through a venturi as shown in the figure at a flow rate of Q= 12 L/s. The inlet and…

A: Q. Flow rate  Q=12 LS=12×10-3 m3SInlet diaD=4.0 cm=4×10-2 m;& throat dia d=35cm=3.5×10-2…

Q: Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1…

A: