A jet of water of diameter 75 mm moving with velocity of 25 m/s strikes a fixed plate in such a way that angle between jet and plate is 60°. Find the force exerted by jet on plate. () in the direction normal to plate (ii) in the direction of jet. V cos 0 V sin 0 V V Fn

A jet of water of diameter 75 mm moving with velocity of 25 m/s strikes a fixed plate in such a way that angle between jet and plate is 60°. Find the force exerted by jet on plate. () in the direction normal to plate (ii) in the direction of jet. V cos 0 V sin 0 V V Fn

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Find the rate at which a fluid flowing with constant velocity u (3,0,-1) crosses each of the following triangles: (а) [(-2, 1, 0), (5, 3, -1), (8, -5, 2)], (b) [(8, -5, 2), (5, 3,-1), (-2, 1,0)), (c) [(1,-1,0), (2, 0, 2), (3, –2, –3)), (d) [(0,0,0), (0, 1,0), (1,0,0)], (e) [(1,0,0), (0, 1,0), (0,0, 1)], (f) [(0,0,0), (0,0, 1), (0, 1, 0)), (g) [(0,0,0), (1,0, 0), (0,0, 1)].
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
Consider the flow of a fluid at speed v0, through a cylindrical pipe of radius r. What would be the speedof this fluid at a point where, because of a constriction in the pipe, the fluid is confined to a cylindricalopening of radius r/4?
Linear Momentum Eq Problem
Part 2 Calculate the component of the velocity in the 0-direction. Answer: V₂ = i 1 m/s Vo 0 e o
Air is flowing parallel to the plate at U∞=5 m/s and T∞=300 K over the flat plate of length L=0.1 m anddepth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find;a) Boundary layer thickness at the point x = L of the plateb) Find the total resistance force acting on the two surfaces of the plate.c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. Thevelocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and they component of velocity v.
Solve faster
A jet of air having velocity V₁ and cross-sectional area A₁ strikes an inclined plate as shown in the figure. Neglect any effects of viscosity. V₁ (a) Find V₂ and V3 in terms of V₁. Note that the pressure is patm everywhere. (b) Because viscous effects are negligible, there is no way for the air to exert a force on the plate in the tangential (z) direction. Using the coordinate system in the figure, find A₂ and A3 in terms of A₁ and 0. (c) For V₁ = 50 m/s, A₁ = 5 x 10-4 m², and 0 = 60°, find the force required to hold the plate in place. Neglect the weight of the plate. Recall that pair = 1.225 kg/m³.
Full part of question b
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc. a.0.629 b.0.98 c.0.989 d.0.636 PLEASE INCLUDE FIGURE OR FBD
Fluid mechanics question
I need help on this question