A piezometer and a Pitot tube are tapped into a horizontal water pipe, as shown in Fig. below to measure static and stagnation (static + dynamic) pressures. For the indicated water column heights, determine the velocity at the center of the pipe.

Q: Determine the direction of flow through the tube shown in Fig. 4, in which y 50 ib/ft', u = 0.40 p .…

A:

Q: Find the air horsepower of the AHU fan that delivers 25,000 CFM through a 4ft x 4ft duct with a…

A: To find: The air horsepower of the AHU fan. Given: The flow rate is Q=25,000 CFM1 m60 sec=416.67…

Q: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury…

A: we have to judge the use of these manometers in this experiment

Q: 3. Find the rate of flow of water, in 1/s, through a 220 mm-diameter pipe which has a venturi meter…

A: Given: D1 = 220 mm = 0.2m D2 = 140 mm=0.14 m Cd=0.97 h=900 mm =0.9 m

Q: Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to…

A: given data: inlet radius (R1)=110mm=0.110mthroat radius(R2)=55mm=0.055mpressure at inlet…

Q: When a fluid flows through a sharp bend, low pressures may develop in localized regions of the bend.…

A:

Q: 15. Hydraulic oil with a Sg of 0.91 is pumped horizontally in a 2-in. I.D. distribution line at the…

A:

Q: 4.2, there is friction in the piping, which means that an additional pressure equivalent to a height…

A: Given data: Due to friction, the additional pressure equivalent required  = h = 100 m We have to…

Q: A pumping system is required that will a water ride. The system schematic is given below. Note that…

A: Solving the solution (1) of the question in figures

Q: Inlet and throat diameters of a horizontal venturimeter are 250 mm and 100 mm respectively. The…

A: Inlet diameter, d1=250 mm=0.250 m Throat diameter, d2=100 mm =0.100 m Pressure at inlet, P1=15…

Q: nlet and throat diameters of a horizontal venturimeter are 280 mm and 100 mm respectively. The…

A: Given: Inlet diameter of venturimeter (D1)=280mm or 0.280mThroat diameter (D2)=100mm or 0.1mPressure…

Q: Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside…

A: Find the simplified bernoulli's equation for the point A and D.

Q: An air stream enters a variable area channel at a velocity of 30" " m/s with a pressure of 120kPa…

A:

Q: In car service station water flows through a vertical pipe reduced from a pipe of diameter D to…

A: The schematic diagram of pipe is as follows:

Q: Shown below is the water jet flow from a pressurized closed tank. The vertical distance between free…

A:

Q: Question 1: B The diagram shows water leaving a tank through an inverted V-tube. (All answers to be…

A:

Q: 1. Specify the sizes of pipes (cast iron, schedule 40) and the size of the motor to be used for a…

A: Given Data: Flow rate, Q = 50 litres/s = 0.050 m3/s Total static head = 50 m Velocity of fluid in…

Q: Shown below is the water jet flow from a pressurized closed tank. The vertical distance between free…

A: Find the simplified bernoulli equation between point 2 and 3.

Q: A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the…

A: Given: Inlet radius (r1)=0.110mThroat radius (r2)=0.055mPressure P1 at inlet=20N/cm2 or 200kPaVacuum…

Q: 2. A fan draws 1.42 m^3 per second of air at a static pressure of 2.54 cm of water through a duct…

A:

Q: Q1. Complete the following: Theory states that if: Re 3000 ..... 2000 < Re < 3000 .......

A: If( Re is less than 2300) flow is laminar flow , when fluid flow through pipe    If ( Re is greater…

Q: A pipe bends through 900 from its initial direction as shown in fig.13. The pipe reduces in diameter…

A: The flow in pipe will have to follow continuity equation: A1V1 = A2V2 The flow must also follow…

Q: In a wastewater treatment plant, Blower supplies air to the sequencing batch reactor. It is…

A: Write the given data. Cpitot=0.98ρair=1.2 kg/m3ρwater=1000 kg/m3hwater=75 mm

Q: Calculate the pressure reading if L = 1.5 m, ?and the angle= 10 , liquid S.G =0.8

A:

Q: onsider the nozzle of a subsonic sted from the nozzle exit at stanc - the height difference in a…

A: given:V2=50m/sA1A2=2

Q: (Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: A pitot static tube fitted in a pipe of 0.25 m diameter records the difference in stagnation and…

A: Given question belongs to subject Fluid Mechanics and from the topic Pressure measurements.

Q: 3) v/3 The pressure change of a balloon depends on the equation P = C.V (C = 100kPa / m and n = -1 /…

A:

Q: 2. Give the procedures in finding the friction factor f using the Moody Chart. Provide…

A: Introduction:-

Q: 35 + 9.81 (0.3824 – 7-2) = - 49.54 kPa. i.e.Pg=-49.54 kPa. This shows that the given pressure at A,…

A:

Q: Use g=32.2 */sec2 (9.81 m/s2 ) and 60°F (16°C) water unless told to do otherwise. • Google…

A: Given The Bernoulli's equation:Since all losses are insignificant, so we can neglect the kinetic…

Q: A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two…

A: Write the density of water at 20 oC. ρ=998 kg/m3 Write the pitot-static tube formula.…

Q: draws 1.42 m^3 p pressure of 2.54 300 mm diamet

A: given:

Q: Calculations involving retention time involve the following formula, T =, where V is volume and Q is…

A: Given: Total retention time→T=55 min                                       =55×60=3300 sec And…

Q: Its required to pump a liquid of specific viscosity of (15) poise at the rate of (22) iiters per…

A: When a fluid flows through a pipe, two forms of head loss (energy loss) enter the picture: one is…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.