Question 3: The four gears are attached to a steel shaft that is rotating at 4Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20 kW are used by gear A, 20 kW by gear C, and 30 kW by gear D. (a) Find the uniform shaft diameter if the shear stress in the shaft is not to exceed 60 MPa. (b) If a uniform shaft diameter of 100 mm is specified, determine the angle by which one end of the shaft lags behind the other end. -20 kW +70 kW -20 kW -30 kW B 2 m 1.5 m 1.5 m-

Question 3: The four gears are attached to a steel shaft that is rotating at 4Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20 kW are used by gear A, 20 kW by gear C, and 30 kW by gear D. (a) Find the uniform shaft diameter if the shear stress in the shaft is not to exceed 60 MPa. (b) If a uniform shaft diameter of 100 mm is specified, determine the angle by which one end of the shaft lags behind the other end. -20 kW +70 kW -20 kW -30 kW B 2 m 1.5 m 1.5 m-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two parallel shaft connected by spur gears turn in the same direction and having a speed ratio of SR…

Q: The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7…

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: Two solid circular shafts are connected by two rigid ab is a composite shaft. Determine the angle of…

A: The radius of gear B is The radius of gear C is The outer radius of AB is The inner radius of AB is…

Q: A 25.4 mm diameter short shaft is used to transmit 33.3 hp . Determine the shaft speed.

A: The diameter of the short shaft is .The power transmitted by short shaft is .To find:The shaft…

Q: The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73…

A: find the maximum shear stress in the shaft.

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

Q: The 70-mm-diameter solid shaft shown is subjected to torques of 600 N·m and 1400 N·m at points B and…

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1.…

Q: Select the diameter for a solid steel shaft that is to transmit 60 HP at 850 rpm without exceeding…

Q: For the steel shaft shown in Fig. Determine the maximum torque transmitted by any transverse cross…

A: The free-body diagram of the beam can be drawn as, Applying the torque balance,…

Q: (6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3-2.9 ft. Determine: (a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter d3 for steel shaft (3). (c) the rotation angle D/A of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b). Answers: (a) d₁=d₂ = i (b) d3= i (c) & DIA = i (1) L₁ TB. B (2) L2 in. in. o' (3) L3 Tp Mommu D
Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output gear D through a compound gear BC. The number of teeth on the gear A, B, C and D are 16, 32, 12 and 18 respectively. Given: Module = 4mm, pressure angle=20° The tangential force acting on the gear B is N A D В
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
i need the answer quickly
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 267 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 8166 Nm without exceeding a shearing stress of 43.32 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
Determine the angle of twist of the end A of the A-36 steel shaft shown in Fig.a. Also, what is the angle of twist of A relative to C? The shaft has a diameter of 200 mm.
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.