Que. 5.6A centrifugal pump having an impeller of 35 cm outside diameter rotates at 1000 rpm.The vanes are radial at exit and are 7 cm wide. The velocity of radial flow throughthe impeller is 3 m / sec. The velocity in the suction and delivery pipes are2.5 m/s and 1.5 m / s respectively. Neglecting frictional lossesdetermine the height through which pump lifts the water and the horse3-power the pump

Given:- diameter=35cm rotates =1000 rpm width=7cm velocity of radial flow=3m/sec velocity in suction…

having an impeller of 35 cm outside diameter rotates at al at exit and are 7 cm wide. The velocity of radial fl m / sec. The velocity in the suction and delivery pipes m/s respectively. Neglecting frictional losses ght through which pump lifts the water and the horse > - po

having an impeller of 35 cm outside diameter rotates at al at exit and are 7 cm wide. The velocity of radial fl m / sec. The velocity in the suction and delivery pipes m/s respectively. Neglecting frictional losses ght through which pump lifts the water and the horse > - po

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

answer the following
Please correct answer And solve both part
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
A Francis turbine working under a head of 35 m has a wheel diameter of 1 m at the entrance and 0.5 m at exit. The vane angle at the entrance is 90° and guide blade angle is 20°. The water at exit leaves the vane without shock. Velocity of flow in the runner is constant. Determine the speed of wheel in revolutions per second and vane angle at exit. Neglect any type of losses.
A centrifugal pump having outer diameter equal to two times the inner diameter and running at 1000 rpm. Works against a total head of 40 m. The velocity of flow through the impeller is constant and equal to 2.5 m/s. The vanes are set back at an angle 40° at outlet. If the outer diameter of the impeller is 500 mm and width at outlet is 50 mm, the discharge is. (a) 1.963 m³/sec (b) 0.1963m ^3 (c) 0.1963 m³/sec (d) 0.1963 cm³/sec
Point A in the suction pipe is 1 m below the pump. It is mounted with anopen manometer which reads a vacuum of 20 cm of mercury. The pipe is10 cm in diameter and the flow is 35 liters/s of water. Compute the totalenergy at point A with respect to a datum through the pump.
I need the answer as soon as possible
Water is flowing in the straight 100mm diameter coated cast iron as shown in the figure. Due to continous supply, the water level of the reservoir remains constant at all time. By using Darcy Weisbach and Hazen William's formula of head loss, determine the flow rate in the pipe. (Ans.: DW:1786.2 liters/min, HW: 2144.4 liter/min) EL85M 180 m opened end EL50M
I need the answer as soon as possible
A 500 mm diameter pipe carries water at a rate of 500 L/s. A pump in the pipe is used to move the water from point A (El 30 m) to point B (El 40 m). The pressure is 70 kPa in A and 350 kPa in B. Assume a head loss of 3 m from point A to point B. a.What is the velocity of flow? ts) b. What is the head supplied by the pump? c. What horse power must be supplied to the flow by the pump if it is 85% efficient?
In a horizontal 5-inch pipe (ID = 5 in.), water is being delivered at a stable discharge of 25 ft³/s. if the pressure increased from 20 psi to 40 psi after a centrifugal pump, how will the flow velocity be affected? O The flow velocity will increase by 4 times. O The flow velocity will decrease by half. O The flow velocity will remain the same. O The flow velocity will double.
T1. Water is to be pumped from a reservoir at datum level 6.5m to a reservoir at datum level 24.8m at the rate of 55.6 l/s by a pump at datum level 9.2m. The suction pipe is 21m of 200mm diameter, and the delivery pipe is 186m of 100mm diameter, both with friction factor 0.015. What head must be generated by the pump. Answer 89.9m Delivery reservoir ha Z₂ hs Suction reservoir Datum Z₁ Pump