) A nozzle, which reduces from 45mm to 30mm in diameter, discharges water at a rate of 30 L/s. If the pressure at the entrance to the nozzle is 800 kPa and 50 kPa at the outlet, determine the force on the nozzle.

) A nozzle, which reduces from 45mm to 30mm in diameter, discharges water at a rate of 30 L/s. If the pressure at the entrance to the nozzle is 800 kPa and 50 kPa at the outlet, determine the force on the nozzle.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, p = 0.038 N-s/m?) from one…

A: Introduction : Minimum costs for medium transmission through the pipeline, as well as pipe costs,…

Q: In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the…

Q: A liquid of specific gravity SG = 1.62 flows in a 75 mm diameter horizontal pipe. The total energy…

A: Specific gravity of liquid, SG =1.62Diamteter of pipe, D=75mm =0.075mThe total energy at a point, E…

Q: The diameter of an open topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m…

Q: Reservoir A supplies water to a nozzle having a diameter of 8 cm which discharges water 40 m below…

A: Given Diameter,d=8cm Head,h=40m Velocity,V=24m/s To find a.Determine the horsepower produced by the…

Q: The horizontal nozzle in the given figure has D1 = 12 in and D2 = 6 in, with the inlet pressure p1 =…

A: Compute the horizontal force provided by the flange bolts to hold the nozzle fixed?

Q: The centrifugal pump blades are 20 mm in depth at the outlet. The impeller is 250 mm in diameter and…

A: A centrifugal pump's impeller features backward-facing blades that are angled at 30 degrees to the…

Q: Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What…

A: The values and diagram given in the question are as follows The specific gravity of glycerine=1.26…

Q: For the system shown in the given figure calculate the height H of oil at which the rectangular…

Q: 3.18. Water is pumped from a supply reservoir to a ductile iron water transmission line, as shown in…

A: Given : Dia of pipe == 750 mm Pressure at A = 350 kPa

Q: A pump is attached to a fire hydrant, where it is desired to produce a jet that rises to a maximum…

A: The expression of flow rate is given as Q=VA ...(1) Here V is the velocity and A is the…

Q: the pressure at point A for a rotational speed

Q: Q-9 A horizontal nozzle of 30 mm diameter discharges a steady jet of water into the atmosphere at a…

A: Given data- Diameter of the nozzle d=30 mm=0.03 m, Discharge Q=15 litres/s, Q=15×10-3 m3/s The…

Q: Steam enters a long, horizontal pipe with an inlet diameter of D1=12 cm with a velocity of 2 m/s.…

A: mass flow rate is (density *Q) that is (density*AV) so Q=(3.14*.12*.12*2/4)*_(1/0.25799) =.0877kg/s

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

A: Given that :-radius of the sprinkler (r) = 0.152 mDiameter of the nozzle () = 0.00635 mFlow rate (Q)…

Q: 3. A pump is attached to a fire hydrant to produce a jet that rises to a minimum height of 24 m at a…

A: The compressive force per unit area is known as pressure, and it seems to be a vector. Pressure in a…

Q: (3) Water jet 0.05 m- (2) 0.8 m •(1) 8X.X kPa 0.1 m Figure Q2 (b) (i) Determine the flow rate at the…

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: Let Point A at the surface of liquid & Point B at 1m below the surface of liquid. Given density…

Q: A pressurized tank discharges its alcohol through a square orifice (c = 0.64, cy = 0.97). If minor…

A: step 1-

Q: A 7.5 cm diameter orifice (Cv= 0.95, Cc= 0.65) is under ahead of oil (s=0.72). Determine the…

Q: For the system shown in figure, calculate the: 4. 2.4 m a.) volume flow rate of water from the…

Q: c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle…

A: To find (a)Q=? (b)Pa=?

Q: A mixture of high pressure water and steam at a rate of 0.5 kgs-¹ flows up a vertical tube with an…

A: A vertical tube is basically used for carrying high-pressure water and steam at a specific pressure…

Q: 3.21 What is the maximum gage pressure in the odd tank shown in the figure? Where will the maximum…

Q: Calculate the pressure required in the longer section just ahead of the nozzle in the figure shown…

Q: A 10-cm long horizontal nozzle is connected to a 5 cm diameter hose and converges to a 2 cm…

A: Given data in question Diameter of nozzle 5 cm End Diameter of hose 2 cm Length if nozzle 10 cm…

Q: A tank is containing water up to a height of 2 m. Calculate the pressure at the bottom of the tank…

A: given data : depth (h)=2 m

Q: A pump is attached to a fire hydrant to produce a jet that rises to a minimum height of 13.5 m at a…

A: The fundamental point of hydraulics is to comprehend, and control to serve society, the event,…

Q: An open tank contains water at a height of 3.6m. If the water is to be replaced by a liquid whose…

Q: 6:687 Oil (sg = 0.85) h cm 35-mm diameter 100-mm inside diameter Flow B- A+ 1.0 m

Q: A nozzle of inner radius 1.06 mm is connected to a hose of inner radius 9.05 mm. The nozzle shoots…

Q: compute the head lost in the nozzle.

A: Head lost

Q: 2. Given the sg of gasoline as 0.72, find the force on the 2.5 m square bottom of the tank shown in…

A: To find pressure at bottom of tank.

Q: An le Volve Pump open P=150 kPa Water sprotruding entrance

A: Given data in question Diameter of pipe Density of water Dynamic viscosity of water Length of pipe…

Q: A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter…

A: Given data in question Pressure Depth of water Diameter To find out Discharge

Q: Water from a large tank enters into a pipe and discharges to the atmosphere through a nozzle…

A: Diameter of the nozzle, d=100mm Velocity through the nozzle, V=60m/s Head of water in the reservoir,…

Q: A liquid of specific gravity SG = 1.76 flows in a 77 mm diameter horizontal pipe. The total energy…

Q: A well-insulated turbine operating at steady state is shown on the right. Steam enters at 3 MPa,…

Q: The 275-kg circular craft is suspended 100 mm from the ground. For this to occur, air is drawn in at…

A: Given data 275 kg circular craft Density of air = 1.22 kg /m3 velocity = 18 m/s Fluid is…

Q: - The velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a.…

A: Given, Velocity of water on discharge side, V2 = 8 m/s Pressure on the discharge side, P2 = 140 kPa…

Q: ire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X=…

A: a) Given, Velocity = 16 m/s, Let the water reach to the height 'h' m, then Applying Bernoulli…

Q: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial…

A: Static pressure is the difference between the total pressure and static pressure. A centrifugal pump…

Q: Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two…

A: Given data Discharge Diameter Height of oil Specific gravity Specific weight Kinematic…

Q: a) The speed of an aircraft flying at an altitude of 11 km is measured by a pitot-static probe. If…

A: Given data in question Altitude 11 km Differential pressure reading 12.9 kPa Density of air 0.4135…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

d) A nozzle, which reduces from 45mm to 30mm in diameter,
discharges water at a rate of 30 L/s. If the pressure at the
entrance to the nozzle is 800 kPa and 50 kPa at the outlet,
determine the force on the nozzle.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
Argon gas flows through a well-insulated nozzle at steady state. The temperature and velocity at the inlet are 570°R and 150 ft/s, respectively. At the exit, the temperature is 460°R and the pressure is 40 lb/in². The area of the exit is 0.0085 ft². Use the ideal gas model with k = 1.67, and neglect potential energy effects. Determine the velocity at the exit, in ft/s, and the mass flow rate, in lb/s.
A Cylindrical Can open at one end is 20 cm in diameter and 40 cm long. The can welghs 6 N. The can is carefully put in a large tank of water vertically, with 20 cm its open end down so that the air is trapped in It (as shown in given figure). If the air in it can be assumed to undergo 40 cm isothermal compression, calculate the elevations of the water surface inside the Can and the top of the Can relative to the water surface in the tank. The atmospheric pressure is 100 kPa and the temperature is 20°C. (Take : = 9810 N/m³]
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
A 12.5mm diameter orifice at the vertical side of the tank showed a discharge of 60 liters for every 85 seconds at a constant total producing head of 4.5m. Measurement of the jet showed that it travelled 2.4m horizontally while dropping 400mm. Determine the coefficient of discharge. A) No Answer among the choices В 0.612 C) 0.637 D 0.584 E 0.668
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the flow rate of the oil in the pipe if the total head loss from point 1 to point 2 is 12 m of oil. 160mm 200mm EL.200m W.S. El. 150m Oil. Sp.gr.=0.82
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH
Air in a room at T0 = 290 K and P0 = 90 kPa is to be drawn by a vacuum pump through a 3-cm-diameter, 2-m-long adiabatic tube equipped with a converging nozzle at the inlet. The flow in the nozzle section can be approximated as isentropic. The static pressure is measured to be 87 kPa at the tube inlet and 55 kPa at the tube exit. Determine the mass flow rate of air through the duct, the air velocity at the duct exit, and the average friction factor for the duct.
A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up, If the air gage pressure inside the tank is 20©kPa, solve the actual mass flowrate if the coefficient of discharge through the nozzle is 0.6. AIR 20 m O 1.59kg/s O 1.22kg/s O 1.86kg/s O 1.33kg/s
2.) A 90-mm circular orifice is situated 0.5 m from a bottom of a closed cylindrical tank 4 m high contains 2.5 m of water. In order to discharge water at 11 hp, what pressure of air (kPa) is required to be maintained in the air space?
A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?