Water flows from a pressurized tank, through a valve and out a pipe. If Q = 0.1 ft/s, Az = 10 ft, P2=0 psig, D = 1in., h = 5V2/2g, please answer the following questions: 1) the pressure in the tank in psig, 2) sketch the EGL of the system.., 3) sketch the HGL of the system

Q: Both 150 mm square outside 300 mm 450 mm

A:

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Using the continuity equation calculating the jet velocity: AV=AjVj…

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: H.w.: As shown in figure below, determine the pressure at point. A- Hg Ans.: 12.164 KPa Va cuum…

A:

Q: Determine the pressure difference between pipes A and B for the differential manometer shown. Water…

A:

Q: -Air 45° Water dz -Mercury d2 7) Find the difference in pressure between tanks A and B if d, = 1 ft,…

A: Given data, d1= 1ft, d2=6in = 0.5ft d3= 1.5ft d4 = 8in= 0.67ft

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

A:

Q: Q2) What is the pressure at point (B)inside the pipe shown in figure below if the water jet velocity…

A: Given data in question  Diameter Velocity  Elevation  To find out  Pressure at B

Q: The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the…

A:

Q: In the supply system (Q=0.89cfs) shown in the figure, the pressure required at the delivery end is…

A: Q = 0.89 cfs Diameter = 4 in = 0.333 ft Length = 1000 ft Pressure at delivery end = 65 psi Water…

Q: Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What…

A: The values and diagram given in the question are as follows The specific gravity of glycerine=1.26…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A:

Q: D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower…

A: Velocity in the pipe without reducer at section 1 and at the outlet (considering it as 2):…

Q: Describe about the piston with pressure chamber in the statnamic test.

A: The statnamic test is the tests which are used for determining load carrying capacity of deep…

Q: Water flows steadily downward through the pipe shown in the figure below. Viscous effects are…

A:

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of…

A:

Q: (Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node,…

A: g= 9.81m/s2 =32.19ft/s2

Q: Water at 25°C is pumped into the galvanized iron pipe branch consisting of two 50-mm-diameter pipes…

A:

Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…

A: Discharge, Q=2 L/s Diameter of the pipe, D=50 mm Roughness coefficient, k=0.03 mm Opening diameter…

Q: (3) Water jet 0.05 m- (2) 0.8 m •(1) 8X.X kPa 0.1 m Figure Q2 (b) (i) Determine the flow rate at the…

A:

Q: The triangular valve (AB) which weighs 1500 Newtons closed at point A and is free at point B. What…

A: Length of the gate t=2sin50o=2.6108 m Depth of center of gravity from surface of water…

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

A:

Q: Solved problems: SP 1 The diameter in fig are 90 cm and 60 cm, at the larger end the pressure is…

A: Bernaulli equation When the force-momentum equation is applied to an inviscid, incompressible fluid…

Q: 1) Determine the flow in Ips on the orifice between the 2 tanks shown below AIR 25kPa AIR 10kPa OIL…

A:

Q: taining air and water is shown. At the closed end of the manometer the air pressure is 16…

A:

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Given :

Q: Glycerin at 20 °C flows upward in a vertical 75- mm-diameter pipe with a centerline velocity of 3.3…

A: Given: Diameter of pipe, D = 75 mm = 0.075 m Centerline velocity, Vc = 3.3 m/s Length of pipe, L =…

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

A:

Q: -8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the…

A: Given data  Hydraulic head at section-1 (h1) = 66cm  Hydraulic head at section-2 (h2) = 54cm  Length…

Q: Given a three-pipe system, the total 150,000 Pa, and the elevation drop data are:

A:

Q: 9.95. The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head…

A: Given, Diameter of the pipes= 150mm and 50mm Velocity in the 150mm pipe, v2= 0.9m/s Pressure in the…

Q: 15. If the pressure in pipe A is 6 kPa, the SG 0.85 pressure in pipe B = .... .. psig. Water 90 mm…

A:

Q: What is pipe roughness? A pump is located 5 m above the surface of a liquid (y = 8170 M/m³) in a…

A: Given Data : f= 0.03 Dia (d)=0.2 m length (l)=60 m Power = 1.5 KW= 1500 W Length of suction pipe =…

Q: A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A…

A: Given data,  Discharge = 447 GPM Loss of head at A  is 5 times of velocity head of 12 in pipe.  Loss…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?