Q6) A hydraulic system is shown in figure Q6. Assume the system is in equilibrium state (There is no force transmitted), determine: m1 m2 ( Given = A1 g = 9.81 m/s² ) A2 i) The suitable radius R1 in cm. ii) If R1 = R2, which one of the masses (mi or m2) will be lifted up and why? m2= 500 kg m =180 kg Rj = ? R2 =20 cm Figure Q6

Q6) A hydraulic system is shown in figure Q6. Assume the system is in equilibrium state (There is no force transmitted), determine: m1 m2 ( Given = A1 g = 9.81 m/s² ) A2 i) The suitable radius R1 in cm. ii) If R1 = R2, which one of the masses (mi or m2) will be lifted up and why? m2= 500 kg m =180 kg Rj = ? R2 =20 cm Figure Q6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Glycerin flows through a 50-mm-diameter horizontal pipe shown in (Figure 1) such that the pressure at A is PA = 113 kPa, and at B it is pa = 110 kPa. Figure Part A HÅ -3m T= Value Determine the magnitude of the shear stress that the glycerin exerts on the wall of the pipe. Express your answer using three significant figures and include the appropriate units. B. N/m² 1 of 1
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
A box with one inlet and two outlets is shown in the figure below. The fluid is oil with a specific gravity (SG) of 0.79. The weight of the oil in the box is 2500 N. Only the outlets are open to the atmosphere. Calculate the force components Fx and Fy required to hold the box stationary. Neglect the weight of the box. Q3 = 3.0 m3/s V3 = 1.5 m/s V2 = 2.0 m/s 03 = 60° 02 45° Q1 Vị = 2.0 m/s P1 = 4000 Pa = 5 m/s F, F, Fx i 14330.9 N Fy i 5918.47 N II
A swimming pool is 10 ft wide and 20 ft long and its bottom is an inclined plane, the shallow end having a depth of 3 ft and the deep end, 7 ft. Assume the pool is full of water. (Round your answers to the nearest whole number. Recall that the weight density of 62.5 lb/ft³.) (a) Estimate the hydrostatic force (in lb) on the shallow end. 2813 lb (b) Estimate the hydrostatic force (in lb) on the deep end. 15313 (c) Estimate the hydrostatic force (in lb) on one of the sides. (d) Estimate the hydrostatic force (in lb) on the bottom of the pool.
A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure below. The gate is hinged along its top edge and is held in position by the force P. Friction at the hinge and the weight of the gate can be neglected. Determine the required value of P. P= lb 모 Water P Hinge Gate 60⁰ 8 ft 33 ft
Fluid Mechanics. Reg.no : 5393 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
As shown in the figure compute the amount and location of the vertical and horizontal components of the hydrostatic pressure on XY 1. Rectangular 5ft wide 7 W.S X * a= 6ft b= 8ft c= 4ft
Consider the system in (Figure 1). Figure k = 5 lb/in. 1 ft = 1/2x² 1 of 1 Part A Determine the smallest amount the spring at B must be compressed against the 0.3-1b block so that when the block is released from B it slides along the smooth surface and reaches point A. Express your answer in inches to three significant figures. x = Submit Provide Feedback - ΑΣΦ Request Answer vec ? in. Next >
In the figure below, determine the force F (newton) to balance the weight of the cylinder. |ylinder W 44 kN A = 0.323 m? F = ? Plunger, a = 0.00323 m? 4.6 m YOil, s = 0.78 YOil, s = 0.78 Assume that the weight
The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown, determine the mass of the block at D. Give your answer in kg and to 3 significant figures. 3 m- 3 m www. KAC = 20 N/m -4 m- www wwwww B KAB = 30 N/m
In (Figure 1), FA = FB = 610 N. Figure B 0.4 m FA FB A 0.3 m Part A Determine the couple moment acting on the pipe assembly and express the result as a Cartesian vector. Enter the x, y and z components of the couple moment separated by commas. Express your answers in newton-meters to three significant figures. Mc = Submit Provide Feedback - ΑΣΦ Request Answer ↓↑ vec ? N.m Next >
A force of 450 N is exerted on lever AB as shown in the figure. End B is connected to a piston which fits into a cylinder having a diameter of 60 mm. What force FD acts on the larger piston, if the volume between C and D is filled with water? Please provide complete explanation in every solution. Thank you.