Figure 1a shows the forces F₁ and F2 acting on the fluid volume bounded by the curved section in the tank. Use Figure 1b below to illustrate the pressure distribution associated with the forces F₁ and F₂. Also, find the magnitude of the forces F₁ and F2. Assume that the width of the tank is equal to 1 m. water = 9.81 kN/m³ Water F₁ m 6 m 2 m F₂ Figure lb Figure la Gate

Figure 1a shows the forces F₁ and F2 acting on the fluid volume bounded by the curved section in the tank. Use Figure 1b below to illustrate the pressure distribution associated with the forces F₁ and F₂. Also, find the magnitude of the forces F₁ and F2. Assume that the width of the tank is equal to 1 m. water = 9.81 kN/m³ Water F₁ m 6 m 2 m F₂ Figure lb Figure la Gate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

water flows out of a pressurized tank through a smooth pipe with Q = 50 m³ / h. In this problem we will find out how big the pressure p1 must be to produce this volume flow? a) What assumptions and simplifications must be made? b) Find the pressure p1. c) Find the same pressure, but using Bernoulli's equation. Comment, what is the difference?
A swimming pool is 10 ft wide and 20 ft long and its bottom is an inclined plane, the shallow end having a depth of 3 ft and the deep end, 7 ft. Assume the pool is full of water. (Round your answers to the nearest whole number. Recall that the weight density of 62.5 lb/ft³.) (a) Estimate the hydrostatic force (in lb) on the shallow end. 2813 lb (b) Estimate the hydrostatic force (in lb) on the deep end. 15313 (c) Estimate the hydrostatic force (in lb) on one of the sides. (d) Estimate the hydrostatic force (in lb) on the bottom of the pool.
Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure
6.2 At the concrete dam bottom shown in the figure, a pipe of diameter d takes water through a water turbine and discharges it into the 2/3 atmosphere. If the water head is h, the friction loss through the suction pipe is H1, and the pressure at the turbine inlet is p gage. Determine the fluid power P in kW that delivered by the turbine. Water h Concrete dam h = 85 m d = 140 mm p = 12.5 bar HL =10 m
H =2m Seawater y = 0.2x2 y 25 m The concrete seawall given in Figure 4 has a curved surface and restrains seawater at a depth of 2 m. The trace of the surface is a parabola as illustrated. Determine the force of the fluid force (per unit length) with respect to an axis through the toe (point A). 1024kg/m³) (Y seawater = -X
As shown in the figure compute the amount and location of the vertical and horizontal components of the hydrostatic pressure on XY 1. Rectangular 5ft wide 7 W.S X * a= 6ft b= 8ft c= 4ft
The following figure shows a tank that contains water. Determine the modulus of the pressure force on the 3-m wide gate AB and its center of pressures.
Water is flowing with flow rate 5 liter/s in a straight 50 mm diameter galvanized iron pipe as shown in the figure. Determine the pressure difference between point A and B by using Darcy-Weisbach formula, and Hazen-William's formula
A beaker of height 1m is filled with water, and the system is at rest. The pressure is measured at two different points, which are marked as P1 and P2. Pressure P1 is measured at the top surface, and pressure P2 is measured at 1 m from the bottom surface. Identify the correct relation between P1 and P2. O P1 = P2, and both are not equal to 0 P1 > P2 O P1 < P2 O P1 = P2=0
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
The overhang wall shown in (Figure 1) is 2.5 m wide. p = 1000 kg/m³. Part A FR = Determine the magnitude of the resultant hydrostatic force the water exerts on the face AB in of the overhang. Express your answer to three significant figures and include the appropriate units. μA 0 = A Value 2 m B Units PER ? Part B Determine the direction of the resultant hydrostatic force the water exerts on the face AB of the overhang. Express your answer using three significant figures. 15] ΑΣΦ | 4 | vec www. ? °, measured counterclockwis from the positive axis
A reservoir contains two different fluids is shown in the figure. The height of the water is 8 m, and the height of the oil (SG = 0.86) is 4 m. a. Determine the density of the oil. b. Determine the pressure between the oil and water in kPa. C. Determine the pressure at the bottom of the reservoir in kPa. OIL WATER