Q2) The motor-pump system shown in figure is modeled as a rigid bar of mass m = 50 kg and mass moment of inertia J. = 100 kg-m². The foundation of the system can be replaced by two springs of C.G. m. Motor Pump CG. stiffness ki = 500 N/m and k2 = 200 N/m Determine the natural frequencies of the system. Base Foundation (b)

Q2) The motor-pump system shown in figure is modeled as a rigid bar of mass m = 50 kg and mass moment of inertia J. = 100 kg-m². The foundation of the system can be replaced by two springs of C.G. m. Motor Pump CG. stiffness ki = 500 N/m and k2 = 200 N/m Determine the natural frequencies of the system. Base Foundation (b)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve this with FBD
A rigid block of mass m can be supported in each of the four ways shown. Each column consists of an aluminum tube that has a 44- mm outer diameter and a 4-mm wall thickness. Using E= 70 GPa and a factor of safety of 2.9, determine the allowable mass for each support condition. (Round the final answers to one decimal place.) m m DI 4 m (1) (2) The allowable mass for case (1) is The allowable mass for case (2) is The allowable mass for case (3) is The allowable mass for case (4) is m (3) kg. kg. kg. kg. m (4)
The 9-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m 0 B HA 2 m 50 N·m 1 of 1 Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. A= [5] ΑΣΦ ↓1 vec 1 Submit Provide Feedback Request Answer ?
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. 4.0 m po Answers: BC= A 4.0 m BE = EF= i i i B 4.0 m 4.0 m 2.5 m E 12.5 KN 4.0 m kN 2 2 2 kN kN D
Please solve.it .
Pls answer asap
2. The bending moment acting on the triangular cross section of a beam is M = 3.6 kN m. Determine the maximum tensile and compressive bending stresses acting on the cross section. M 120 mm 60 mm-
The 5.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m- 0 B 2 m 50 N·m 1 of 1 Part A Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. 0 = for Part A for Part A for Part, A for Part A undo for Part A redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A Submit Provide Feedback Request Answer Next >